35
AT Command List
AT commands available on FOMA terminal
d
The following abbreviations are used in the AT command list;
[&F]
: Command of which setting is initialized by AT&F command.
[&W] : Command of which setting is saved by AT&W command. The setting can be retrieved by ATZ
command.
d
When you make a call via an external device or using AT command, the call is made from Number A in
A mode/Dual mode, and from Number B in B mode.
Modem port command list
The followings are the usable commands for "FOMA N01A (
モデム
)" (modem):
AT command
Outline
Parameter/description
Command execution example
A/
Executes the last executed
command again. No carriage
return is necessary.
−
A/
OK
AT
−
The modem function of a FOMA terminal is
controllable by adding the command of this
table after this command.
* OK is answered even when only AT is entered.
AT
OK
AT%V
Displays the version of the
FOMA terminal.
−
AT%V
Ver1.00
OK
AT&C
n
[&F] [&W]
Selects the operating
condition of the circuit CD
signal to DTE.
n
= 0
:
CD is always ON.
n
= 1
:
CD changes according to the carrier of
the other party's modem (initial value).
AT&C1
OK
AT&D
n
[&F] [&W]
Selects the operation to
take place when the circuit
ER signal received from DTE
transits between ON and
OFF.
n
= 0
:
Ignores ER status (always assumed
to be ON).
n
= 1
:
When ER changes from ON to OFF, it
becomes an on-line command status.
n
= 2
:
If ER changes from ON to OFF, a
connection is disconnected and it will be in
an off-line command status (initial value).
AT&D1
OK
AT&E
n
[&F] [&W]
Selects how to display the
connection speed.
n
= 0
:
Displays the wireless network
transmission speed.
n
= 1
:
Displays the DTE serial transmission
speed (initial value).
AT&E0
OK
AT&F
n
Restores all of registers to
their defaults. If this
command is input during
communication, the line will
be disconnected.
Only
n
= 0 can be specified (can be omitted).
(At the time of off-line
mode)
AT&F
OK
AT&F?
ERROR
AT&F
=
?
ERROR
(At the time of on-line
command mode)
AT&F
NO CARRIER
(Change to off-line
mode)
AT&S
n
[&F] [&W]
Sets the Data Set Ready
signal to be output to DTE.
n
= 0
:
DR is always ON (initial value).
n
= 1
:
DR signal is ON when the line is
connected (when the communication
call is established).
AT&S0
OK
Summary of Contents for PRIME series N-01A
