61
Voice/Vi
deophone Calls/P
ushTalk
V.phone settings
……
Set the screen for videophone
calls.
Visual prefer.
……
Select Normal/Prefer img qual/
Prefer motion spd for an image sent to and received
from the other party.
This setting is only retained during the call.
Brightness
……
Adjust the brightness between five
levels (–2 to 0 to +2).
White balance
……
Set image color tones.
→
p.235
This setting is also applied to the equivalent camera
functions.
Color mode set
……
Select Normal/Sepia/
Monochrome as an image effect.
This setting is only retained during the call.
Chara-den set.
……
Set the following when Chara-den is
used. This setting cannot be set for the camera images.
Switch Chara-den
Action List
Change Action
Switch image
……
Display an image selected in
“Substitute image” (p.81) on the other party’s display.
Display light
……
Set the backlight.
All time ON
Same as backlight
……
Turn on the backlight
according to “Lighting” under “Backlight”.
FrontCamera Rev.
……
Set whether to display your
camera image as a mirror image (ON) or normal image
(OFF) on your FOMA terminal during a call.
Own number
……
Display your phone number during a
videophone call.
Send DTMF tone
⇔
DTMF tone OFF
……
Set/Release
push signal transmission mode during Chara-den.
Videophone calls other than Chara-den are always in
push signal transmission mode.
Change to voice
→
p.62
Loc. notification
→
p.323
●
If a videophone call is not connected
When a videophone call is not connected, the cause
of the failure appears.
z
The cause may not appear depending on the
situation.
z
Depending on the type of the other party’s phone or
network service subscription, the reason may not
accurately reflect the other party’s actual status.
z
If the videophone call is not supported, your call is
automatically switched to a voice call when you set
“Auto redial as voice” to “ON”. However, the
videophone may not work properly if you call an
ISDN synchronous 64K access point, 3G-324M-
incompatible ISDN videophone (as of October,
2008) or if you dial a wrong number. Call charges
may apply.
Display
Cause
Check number then
redial
The dialed phone number is not
in use
Busy
The line is busy
• This message may also appear
during packet communication,
depending on the other party’s
terminal.
Busy with packet
transmission
The other party is using packet
communication
Out of service area/
power off
The other party is out of service
area or the phone is turned off
Your call is being
forwarded
The call is being forwarded (a
videophone call is made when
the forwarding number is for a
3G-324M-compatible
videophone)
Redial using voice
call
The forwarding phone is not
compatible with videophone
Please activate
caller ID before
dialing again
The other party has set the
Caller ID request service
This number is not
available
The other party has set the
Nuisance call blocking service
Upper limit has
been exceeded
Connection failed
The upper limit set for a Limit
billing plan (Type Limit or Family
Wide Limit) is exceeded
Connection failed
You attempted to connect
without notifying your caller ID
(when dialing into visualnet, etc.)
• This message may also appear
in other situations.
Set Caller ID Notification to “ON”
and retry.
Please make your
call from the i-mode
web page
You attempted to make a
videophone call to watch V-live
without browsing the i-mode
official site
Summary of Contents for PRIME series N-01A
