75
Continued on next page
Voice/Vi
deophone Calls/P
ushTalk
■
To mute the ring tone
X
Press
g
at “Level 1”
The icon on the standby screen indicates which
items are set to “Silent”.
: “Silent” is set for “Phone”, “Videophone”
and/or “PushTalk”
: “Silent” is set for “Mail”, “Chat mail”,
“MessageR” and/or “MessageF”
: Both “
” and “
” are set
Holding Incoming/Current
Calls
<On hold/Holding>
<Example: To put an incoming call on hold>
1
While ringing
X
y
Three short beeps sound
and the call is put on hold.
The caller hears an
announcement that you
cannot answer now, and the
call is put on hold.
■
To put the current call
on hold
X
During a call
X
t
■
To end the call during on hold/call hold
X
y
2
Press
r
to resume the call
You can also press
t
to resume the held call.
Setting the hold tone
<Hold tone setting>
Set the announcement to be played to the caller
during on hold.
z
You cannot change the hold tone played during a
call.
1
i
X
“Settings/Service”
X
“Talk”
X
“Hold tone setting”
X
“On hold
tone”
X
Select a tone
Select “Tone 1”, “Tone 2”, “Voice announce 1
*
” or
“Voice announce 2
*
”.
*: Not available when no voice announcement is
recorded.
Using the Public Mode
Public mode (Driving mode/Power OFF) is an
automatic answering service provided for public
places and circumstances in which mobile phones
should not be used.
z
When Public mode and network services are set
concurrently, Voice Mail service
*1
, Call Forwarding
service
*1
and Caller ID Request service
*2
take
precedence over Public mode.
*1: For a voice call whose ring time is not “0 second”, a
service activates after the Public mode
announcement is played.
*2: When the caller notifies the caller ID, Public mode
activates.
z
Public mode does not work for a call from a phone
number registered for Nuisance Call Blocking.
Using Public Mode (Driving Mode)
<Public mode (Driving mode)>
When Public mode is set, a caller hears a message
that you cannot answer the call because you are
driving or in a place where you have to refrain from
using a mobile phone (on a train or bus, in a theater,
etc.), then the call ends.
z
Public mode can only be set or released from the
standby screen (can also be set or released when
“
” is displayed.).
z
You can make calls when Public mode is set.
z
This function is not available during data
communication.
z
When you receive a call with no caller ID while
Caller ID Request service is set to “Activate”, the
caller ID request announcement is played (Public
mode announcement is not played.)
N
z
The ring volume setting specified for “Phone” in
this function is also applied to the “Select ring
tone” setting for a voice call, and the alarm tones
for “Schedule” and “To Do list”.
z
Even if the Ring volume is set to “Level 3” - “Level
6” or “Step”, the ring tone is played at “Level 2” in
the following cases:
• Immediately after a voice call/videophone call
ends
• Immediately after a PushTalk call ends
• Immediately after a Record message/Voice
memo recording ends or during playback
• During/immediately after “Voice announce”
recording
N
z
Call charges apply while an incoming call or
current call is put on hold.
Summary of Contents for PRIME series N-01A
