3
1) 多可由多个零件组装而成 , 在使用过程中会造成零件松动 , 请及时检查并紧固好零
件。
Check frequently to make sure all parts are still firmly tightened and functioned properly.
2) 多可的所有零件都为官方测试的合格零件 , 但如果不按操作说明 , 超过零件的装配
力矩 (25NM) 或产品的承重载荷会损坏零件。
Never exceed the maximum weight and assembly force(25nm).You can find the maximum
weight for every specific ride in our manual.
3) 应尽量避免暴露在阳光 , 水 , 沙堆 , 泥土等会造成其老化和缩短使用寿命的环境因
素。
Avoid streets and Excessive exposure to sunlight ,water, sand, gravel, and other debris that will
shorten the life of the docyke .
4) 应避免接近尖锐的物体 , 以免刮伤其表面 , 同时尽量在平缓的地区使用。
Avoid sharp bumps, drainage grates and sudden surface changes. Ride on smooth, paved
surfaces.
5) 多可 由很多小零件组成 , 部分表面尖锐 , 请妥善保管并放置于儿童无法接触到的地
方 , 以免被幼儿误食或弄伤。
Before assembly,present a choking hazard to children under the age of three. Care should be
taken during unpacking and assembly to insure that all small parts and plastic bags are accounted
for and kept out of the reach of children.
6) 多可 不用时请放置在干燥的地方妥善保管。
Dirt,1eaves,and other debris can damage, shrink,expand or weaken docyke parts.
Keep your ride in a dry environment.
7) 多可 除螺钉外其余都为特别设计的零件 , 请不要和市场上类似零件混用。
Most of the docyke's components are specially designed, please do not mix with similar parts
on the market.
8) 检查充气轮胎气压不能大于 1.8bar(1.8 kgf/cm
²
)
Check the air pressure in the tires to max 1.8bar.
10) 适当着装 , 不要穿宽松衣物或饰品 , 让衣服 , 头发远离运动部件 , 避免卷入其中。
Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves
away from moving parts. Avoid caught in moving parts.
11) 佩戴好个人防护装置 , 安全装置后使用 多可 , 如防滑鞋 , 安全帽 , 等。
Use personal protective equipment. Always wear protective equipment such as non-skid
safety shoes, hard hat etc.
12) 在进行任何调节 , 更换附件或储存 多可 之前必须使电池与产品脱开 , 减少以外启
动危险。
Disconnect the battery pack from the DOCYKE before making any adjustments, changing
accessories, or storing DOCYKE.
多可 使用规范:
DOCYKE use specification
Summary of Contents for GK-06
