background image

Operating Instructions and Parts Manual

 Surface Mount 

Hand Dryer

High-Speed

BC2009

ITEM CATEGORY

Operating Voltage

Output 

Warm Air Temp

Warm Air Speed Output

Motor Type

Motor Thermal Protection

Heater Element

Heater Thermal Protection

Drying Time

Stand-by Power

Circuit Operation

Sensor Range

Timing Protection

Sound Level

Drip proof

Isolation

Net Weight

Shipping Weight

Unit Size

PERFORMANCE DATA

220-240 Vac, 50/60 Hz, 0.84-1.0 kW

55 °C [131 °F] at ambient T = 25 °C [77 °F], MAX, Adjustable by Owner

 m/s,

 adjustable

95-115

325-500 W,

 

22000-29000 r.p.m., 

Adjustable

; Brush Type, Dual Ball Bearings

Auto Resetting Thermostat turns unit off at 95 °C [203 °F]

Range Adjustable by Owner, 325-500 W 

Auto Resetting Thermostat turns unit off at 85 °C [185 °F]

Thermal fuse cuts unit off at 142 °C [288 °F]

Less than 15 seconds

Less than 0.5 W

Infrared Automatic, self adjusting

Standard [170 ± 20 mm], 

Adjustable

, The range is [100-230 mm]

60 seconds auto shut off

 MAX @ 1m

MIN 69 dB to 76.6 dB

IP24

CLASS 1

4.0 kg

4.5 kg

191.4 mm (W) x 295.4 mm (H) x 101 mm (D)

BC2009 - 

Stainless steel (#304), Satin finish (t:1.2 mm)

COVER TYPE/ COVER FINISH

Ver.A0

191.4 mm

101 mm

295.4 mm

TECHNICAL SPECIFICATIONS

1

Summary of Contents for BC2009








Reviews: