background image

Page 7

Door/Window Sensor Advanced User Manual

Inclusion & Exclusion

Inclusion (Add to System)—New Installation

1.  For proper inclusion, bring the Door/Window Sensor to the final location where 
it will be used*.
2.  Follow the instructions for your Z-Wave controller to enter inclusion mode.
3.  Remove the Battery Tab protruding from the Battery Tab Slit.
4.  The device will automatically enter inclusion mode for two minutes and the 
LED Indicator will alternate between green and red.
Upon successful inclusion the LED Indicator will flash green three times then stop 
blinking.

Inclusion (Add to System) —Re-Installation

1.  For proper inclusion, bring the Door/Window Sensorto the final location where 
it will be used*.
2.  Follow the instructions for your Z-Wave controller to enter inclusion mode.
3.  Remove the Sensor Cover and the LED Indicator will start blinking yellow.
4.  Press the Button quickly 3 times in a row.
5.  The device will enter inclusion mode for two minutes and the LED Indicator will 
alternate between green and red.
After successful inclusion, the LED Indicator will flash green three times then 
blink red until the cover is replaced.

Exclusion (Remove from System)

Follow the instructions for your Z-Wave Certified Controller to enter exclusion 
mode.  When prompted by the controller:
1.  Remove the SENSOR COVER and the LED Indicator will start blinking red.
2.  Press the Button quickly 3 times in a row.
The LED Indicator will flash green three times indicating exclusion/disconnection 
and will then continue flashing red (indicating tamper) until the cover is replaced.

*For non Z-Wave Plus networks, please consult the owner’s manual for your primary controller to determine the best method and location 

for adding the Door/Window Sensor to your Z-Wave network.

Inclusion & Exclusion

Summary of Contents for DMDP1





















Reviews: