background image

28

If the fuse requires replacing at any time, the fuse cover/carrier should be

removed using a small screwdriver to lever it out. The old fuse should be

replaced  by  a  3  amp  ASTA  approved  BS  1362  fuse  and  the  fuse

cover/carrier must be refitted before the plug is used again.
If  the  fuse  cover/carrier  is  lost,  a  replacement  can  be  obtained  from  the

service shops. The fuse cover/carrier must be of the same colour as that of

the coloured insert in the base of the plug. In no circumstances must the

plug be used without a correct fuse cover/carrier fitted.
If the plug supplied on the mains lead is not suitable for the socket in your

home, it should be cut off and disposed of safely, or destroyed, to avoid any

possible shock hazard resulting from the plug being inserted into a 13 amp

socket elsewhere in the house. A suitable replacement plug should then be

fitted as given below.
General guide to fitting any plug
Ensure  the  lengths  of  wire  inside  the  plug  are  prepared  correctly.

Connections should be firmly made after all conductor strands are entered

into  the  terminal  posts.  When  preparing  the  cable    ends  take  care  not  to

damage the outer sheath, or the insulation surrounding the inner conductors.

Tighten all screws. Replace the top cover of the plug and secure.
Other versions
Your refrigerator has a 3-wire mains lead which is intended for connection

to a 3-pin plug and a properly earthed socket outlet.
IMPORTANT:

The wires in the mains lead of this appliance are coloured

in accordance with the following code:
GREEN-AND-YELLOW: EARTH      BLUE: NEUTRAL       BROWN: LIVE
As the colours of the wires in the mains lead may not correspond with the

coloured markings identifiying the terminals in your plug, proceed as follows:

the  wire  which  is  coloured  GREEN-

AND-YELLOW  must  be  connected  to  the

terminal  in  the  plug  which  is  marked  with  the

letter E or by the earth symbol

or coloured

green  or  green-and-yellow.  The  wire  which  is

coloured  BLUE  must  be  connected  to  the

terminal  which  is  marked  with  the  letter  N  or

coloured  black.  The  wire  which  is  coloured

BROWN  must  be  connected  to  the  terminal

which  is  marked  with  the  letter  L  or  coloured

red.

GB

Summary of Contents for RC1600

















Reviews: