background image

11

DIAGNOSTIC SERVICE MANUAL

DIAGNOSTIC SERVICE MANUAL

DIAGNOSTIC SERVICE MANUAL

DIAGNOSTIC SERVICE MANUAL

DIAGNOSTIC SERVICE MANUAL

Dometic

Dometic

Dometic

Dometic

Dometic

®  

®  

®  

®  

®  

RM3604/3804 AES

RM3604/3804 AES

RM3604/3804 AES

RM3604/3804 AES

RM3604/3804 AES

®

®

®

®

®

Refrigerators

Refrigerators

Refrigerators

Refrigerators

Refrigerators

SECTION 7

SECTION 7

SECTION 7

SECTION 7

SECTION 7

WIRING

WIRING

WIRING

WIRING

WIRING

7.1

7.1

7.1

7.1

7.1

EXTERNAL WIRING

EXTERNAL WIRING

EXTERNAL WIRING

EXTERNAL WIRING

EXTERNAL WIRING

1.

1.

1.

1.

1. 120 Volts AC Connection

120 Volts AC Connection

120 Volts AC Connection

120 Volts AC Connection

120 Volts AC Connection
The refrigerator is equipped with a three-prong
(grounded) plug for protection against shock hazards
and should be plugged directly into a properly
grounded three-prong receptacle. Do not cut or
remove the grounding prong from this plug.

2.

2.

2.

2.

2. 12 Volt DC Connection

12 Volt DC Connection

12 Volt DC Connection

12 Volt DC Connection

12 Volt DC Connection
Connection is made to the main terminal block. The
refrigerator must be connected to the battery circuit
with two wires of adequate capacity to avoid voltage
drop.

The wire gauge should be chosen with consideration
to the wire length in accordance with the Table
below.

MAXIMUM CONDUCTOR WIRE LENGTH IN FEET

MAXIMUM CONDUCTOR WIRE LENGTH IN FEET

MAXIMUM CONDUCTOR WIRE LENGTH IN FEET

MAXIMUM CONDUCTOR WIRE LENGTH IN FEET

MAXIMUM CONDUCTOR WIRE LENGTH IN FEET

AWG

RM3604

RM3804

10

17

17

8

27

27

Do not use the body or chassis of the vehicle as a
substitute for either of the two conductors. No other
electrical equipment or lighting should be connected
to the refrigerator circuit. The refrigerator will draw 18
amps at 12 volts.

CAR BATTERY

IGN.

SWITCH

MIN 10-GAUGE

FUSE WITHIN 18" OF BATTERY

8-GAUGE CHARGE

8-GAUGE CHARGE

8-GAUGE CHARGE

8-GAUGE CHARGE

8-GAUGE CHARGE
LINE FROM TRAILER

LINE FROM TRAILER

LINE FROM TRAILER

LINE FROM TRAILER

LINE FROM TRAILER
PLUG TO TRAILER

PLUG TO TRAILER

PLUG TO TRAILER

PLUG TO TRAILER

PLUG TO TRAILER
BATTERY

BATTERY

BATTERY

BATTERY

BATTERY

CONNECTOR

8-GAUGE CHARGE  RECOMMENDED

8-GAUGE CHARGE  RECOMMENDED

8-GAUGE CHARGE  RECOMMENDED

8-GAUGE CHARGE  RECOMMENDED

8-GAUGE CHARGE  RECOMMENDED
TRAILER CONNECTOR

TRAILER CONNECTOR

TRAILER CONNECTOR

TRAILER CONNECTOR

TRAILER CONNECTOR

16-GAUGE, TAG LINE, FROM TOW VEHICLE
IGNITION SWITCH TO REFER
IGNITION   POSITION

16-GAUGE SIGNAL WIRE

TO DISTRIBUTOR

ISOLATOR

ALTERNATOR

BATTERY

Summary of Contents for RM3604

















Reviews: