background image

Installation, Operation and Maintenance manual

2

PowerCore

®

 Dust Collectors  - Series CPV

TABLE OF CONTENT

SAFETY RECOMMENDATIONS ................................................................................................... 4
INSTALLATION ............................................................................................................................. 7

Product information ............................................................................................................. 7
General guidance to lifting ................................................................................................... 8
Mounting over aperture ....................................................................................................... 9
Compressed air requirements ............................................................................................. 9
Controller ............................................................................................................................10
Collectors with integral fan .................................................................................................10
Overload protection ............................................................................................................11
Control of ancillary equipment and interlocks .....................................................................11
EEx controls .......................................................................................................................11
Explosion protection ...........................................................................................................12
Antistatic earthing ..............................................................................................................12
Installation check list ..........................................................................................................12

COMMISSIONING .......................................................................................................................13

Installation check list ..........................................................................................................13
Start-up sequence ..............................................................................................................13
Shut-down sequence .........................................................................................................14

OPERATION ................................................................................................................................15

Principle of operation ..........................................................................................................15

MAINTENANCE ...........................................................................................................................16

Routine inspection ..............................................................................................................16
Servicing schedule .............................................................................................................17
Filter pack replacement ......................................................................................................19
Fan assembly removal/replacement .................................................................................. 20

SPECIFICATION .......................................................................................................................... 25

Summary of Contents for CPV-12



























Reviews: