2
ED100LE
02-2021
DL4616-001
dormakaba ED100LE operator – Fine cover
Installation Instructions
Table of Contents
Table of contents
2
1
General information
3
1.1
General information
3
1.2
Single door configuration examples
4
1.3
Double door configuration examples
4
2
Product overview
5
2.1
ED100LE low energy operator
5
2.3
Axle extensions, ED100LE
6
2.4
Push arm door stop - option
6
2.5
Fine cover kit – basic
6
2.6
Fine cover professional cover kits – option
7
2.7
Push arm kits
8
2.8
Deep pull arm kit
8
2.9
Arm screw kits
8
2.10 Optional key switch panels
8
2.11 Double door ED100LE operator
connection cables
9
3
Technical data
9
3.1
ED100LE operator technical data
9
3.2
ED100LE operating specifications
10
4
ED100LE terminal board interfaces
11
4.1
ED100LE terminal board interfaces
11
5
ED100LE door signage
12
5.1
Low energy operator
12
5.2
Door signage, low energy swing door per
ANSI / BHMA A156.19
12
5.3
Safety label, low energy swing doors
13
6
Recommended tools and torque chart
14
6.1
Recommended tools
14
6.2
Standard tightening torque
14
6.3
Drill bits
14
7
Installation templates
15
7.1
ED100LE installation templates
15
8
ED100LE operator installation
20
8.1
Installation preparation
20
8.2
Remove mounting plate from ED100LE
operator 21
8.3
Customer 115 Vac connection to
mounting plate terminal block
22
8.4
Mounting plate attachment to jamb or
wall 24
8.5
Connect customer 115 Vac to mounting
plate terminal block
25
8.6
Route accessory wiring to mounting plate
25
8.7
Remove protective film strips from
ED100LE operator
26
8.8
Install ED100LE operator onto mounting
plate 26
9
Push arm installation
27
9.1
Push arm installation templates
27
9.2
Push arm installation
27
Table of contents
10
Pull arm installation
30
10.1 Pull arm installation
30
10.2 Pull arm assemblies
30
10.3 Pull arm hardware
30
10.4 Install hardware into track
31
10.5 Assemble slide shoe
31
10.6 Assemble drive arm and CPD lever
32
10.7 Fasten drive arm to ED100LE operator
33
10.8 Install track assembly
34
11
ED100LE Operator spring tension
35
11.1 Set operator spring tension
35
12
ANSI/BHMA standards
36
12.1 ANSI/BHMA A156.19 Low Energy Power
Operated Swinging Doors
36
13
Install door signage, low energy door
37
13.1 Install door signage
37
14
Cover, end caps and spindle caps
37
14.1 Cover end cap and spindle installation
37
15
Maintenance
38
15.1 Safety label, low energy swing doors
38
15.2 Arm fasteners – torque requirements
39
16
Companion door installation
40
16.1 ED100LE Companion installation
templates 40
16.2 8616 closer and adaptor
42
16.2.1 Companion door 8616 Door closer data
42
16.3 Select installation template
43
16.4 Assemble ED100LE and closer backplates
43
17
Companion door, push arm installation 44
17.1 Mount backplate, push arm application
44
17.2 Install 8816 closer on backplate –
push arm mounting
45
17.3 Push arm installation
46
18
Companion door, pull arm installation
48
18.1 Mount backplate, pull arm application
48
18.2 Install 8816 closer on backplate –
pull arm mounting
49
18.3 Pull arm installation
50
19
8816 closer adjustments
53
19.1 8816 door closer adjustments
53
Appendix A - Fine cover professional cover kits
54
A.1
Professional cover kit HK3401-05X
installation instructions – single door
54
A.2.1 Professional cover kit HK3401-07X
installation instructions – pair
57
Appendix B - Key switch wiring diagrams
59
B1.1 HX4604-21C Key Switch Panel with RJ45
connector
59
B2.1 HX4604-11C Key Switch Panel
60
Appendix C - Knowing act switch wiring
61
diagrams 61
C1.1 Knowing act switches
61
C1.2 Knowing act switch wiring diagram
61
