background image

 

 

 

             Page 9 

Clockwise turning of the large 
gear will retract the bolt pin. 

Anti-clockwise turning of the large 
gear will extend the bolt pin. 

The GL10 features multiple locking / unlocking to allow for misaligned gates or unforeseen problems. If the bolt pin 
meets an obstruction as it is trying to secure the gate, it stops and withdraws before attempting to lock again. It has 
a total of three attempts to secure the gate after which time it will sound an alarm. The same function is present when 
the GL10 unlocks. 

 
 
7.3 General 

 
If the batteries are fitted and the power is removed to the GL10 at any time during its operation, the lock will revert to 
its  pre-selected  state  of  either  unlocked  or  locked.  The  GL10  has  been  designed  to  operate  with 

high  quality 

disposable alkaline batteries

 and may not work correctly with alternatives. Should the batteries become flat the 

lock will sound an alarm to indicate a battery change is required.   
 
If  the  batteries  are  not  replaced  once  they  have  become  depleted,  the  GL10  will  automatically  revert  to  the  Fail 
Maintained state; i.e. in the event of a power failure the lock will stay in the position it was in before the power was 
removed. 
 
The three monitors can be used to provide door and bolt position information regardless of the locks configuration. 
 
Manual operation of the GL10 is available by removing the cover to allow access to the lock mechanism. The supplied 
key can be used to open and remove the cover and once access is available a screwdriver can be inserted into the 
centre of the large gear and turned to move the bolt pin in or out.     
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

7.4 Alarms 

 
To offer instant feedback about the locks state, the GL10 has an on board beeper which sounds at various times. 
The table below details the different alarms expected from the GL10.  
 
  

Locked confirm 

1 Short beep 

Unlocked confirm 

2 Short beeps 

Failure to lock / unlock 

5 Long beeps 

Battery replacement 

5 Short beeps sounded 5 seconds after a lock activation and repeated every 
10 minutes until the batteries are replaced 

Diagnostic 

Various beeps 

– used for service 

 
 
 
 

Summary of Contents for GL10













Reviews: