Dormakaba Saflok SR Series Installation Manual Download | Manualshive

Page: 12 / 15

background image

12

Saflok SR

TM

Series RFID Concierge Installation Guide - PK3673_T_07_16

Annex

Programming

SR Controller Programming Port

Programming

Port

The SR RFID Concierge lock can be programmed the following two ways.

1. Through the USB port on the serial interface board of the controller using the standard hand held programming

probe.

2. Through J2 of the SR reader using a special HH6 programming probe (P/N: 71790) that can be purchased

separately.

71790 Programming Cable

71690 Programming Cable

«
...
10
11
12
13
14
...
»

Summary of Contents for Saflok SR Series
















Reviews:

No comments

Related manuals for Saflok SR Series

Brand: Winkhaus Pages: 98

Brand: Kaba Pages: 16

Brand: NCR Pages: 14

Brand: Ojmar Pages: 5

Brand: Assa Abloy Pages: 2

Brand: PDQ Pages: 2

M300 LEGIC L043-A01

Brand: LEHMANN Pages: 22

Brand: G-U Pages: 108

Brand: Yale Pages: 20

Brand: JNF Pages: 2

Brand: Targus Pages: 2

Brand: Dormakaba Pages: 24

Brand: Teknion Pages: 15

Brand: M-LOCKS Pages: 12

Brand: Paxton Pages: 24

Brand: Taymor Pages: 2

TuBAR DWC-ORD-1

Brand: COMPX Pages: 8

Brand: ZKTeco Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands