background image

 

 

           

 

 

 

 

 

 

 

 

 

 

 

 

Owner’s Manual 

2965020 (3700LS-H) 

Instructions for Assembly, Testing, Operation, 

Servicing, & Storage 

 

Log Splitter: Outdoor hydraulic powered machine that 

splits wood logs. 

 

WARNING 

READ and UNDERSTAND this manual completely before using log splitter. 

All operators of this equipment must read and completely understand all safety information, operating instructions, 
maintenance and storage instructions.  Failure to properly operate and maintain the log splitter could result in serious 
injury to the operator or bystanders from moving parts that can crush or cut, flying objects, burns, fire or explosion, 
escaping high pressure hydraulic fluid, or carbon monoxide poisoning.  In particular, be aware of the following 
hazards: 

Crush and Cut Hazards 

Moving parts can crush and cut hands and fingers.  Keep hands clear of endplate, wedge, log strippers, and logs 
while splitting. 

High Pressure Hydraulic Fluid Hazards 

High fluid pressures and temperatures are developed in hydraulic log splitters.  Hydraulic fluid escaping through 
even a pin-size hole opening can puncture skin and cause severe blood poisoning.  Inspect hydraulic system 
regularly for possible leaks.  Never check for leaks with your hand while the system is pressurized.  Seek medical 
attention immediately if injured by escaping fluid. 

Fire Hazards 

 

If your log splitter is intended for use near any ignitable forest, brush, or grassy covered land, the engine 
exhaust should be equipped with a spark arrestor.  

 

Keep a fire extinguisher with you, rated for ordinary combustibles and flammable liquids.

 

 

STOP! 

ASSEMBLY REQUIRED:  

This product requires assembly before use.  See “Assembly” section for instructions. 

INSPECT COMPONENTS.  

Closely inspect upon receipt to make sure no components are missing or damaged.  

See “Assembly” section for instructions on whom to contact to report missing or damaged parts.

 

ADD ENGINE OIL and HYDRAULIC OIL BEFORE USING:

  This product is shipped without engine oil or 

hydraulic oil. DO NOT start log splitter before adding both oils.  See “Assembly” and “Initial Unpacking & Set-
up” sections for detailed instructions.

 

Any Questions, Comments, Problems or Parts Orders 

Call your dealer or Dosko Customer Service 1-800-822-0295

ITEM NUMBER:

 2965020 

 

 

SERIAL NUMBER: 
_______________

 

M2965020D

 

Summary of Contents for M2965020D









































Reviews: