background image

Summary of Important Safety Information for Operation 

30 

 

 

Introduction 

 

Read Manual.

 Read this operator's manual and the engine Owner's Manual completely before attempting to use the 

log splitter.  Serious injury or death can result if safety instructions are not followed. 

 

Instruct operators.

  The log splitter owner should instruct all operators in safe log splitter operation. 

 

Intended use.

  Log splitters should only be used for splitting wood logs, lengthwise with the grain.  Do not use for 

other purposes, as unforeseen hazards may result. 

 

Prohibition Against Modifications 

Never modify or alter the log splitter in any way.  Modifications can create serious safety hazards and will void the 
warranty. 

 

Attachments.

  Never add attachments to the splitter, except for authorized accessories supplied by the manufacturer 

with instructions for safe installation and use. 

 

Engine Speed.

  The maximum engine speed is preset at a safe limit.  Never attempt to modify the engine speed 

setting to run at a higher speed. 

 

Fuel/Exhaust system.  

NEVER modify or add to the exhaust system, fuel tanks, or fuel lines.  Fire can result. 

 

Remote Control.

  NEVER attach a rope, cable, or other remote device to the splitting control. 

 

Splitting Wedge.

  NEVER attempt to change the height or speed of the splitting wedge. 

 

Pressure Setting.

  NEVER increase the pressure setting of the pump or control valve. 

 

Operator Restrictions 

 

Untrained Operators.

  Do not allow anyone to operate the log splitter who has not read the owner's manual or been 

instructed on the safe use of the splitter.

 

 

Minimum Operator Age.

  Never allow anyone under age 16 to operate the log splitter.  Anyone 16 years of age 

and older must be trained and supervised by a trained adult.

 

 

Safety in Moving and Towing the Log Splitter 

 

WARNING

 

The log splitter is very heavy.  It can cause serious injury if it rolls out of control or tips over. 

 

Follow the safety instructions below for safely moving the log splitter. 

 

General safety while Moving 

 

Horizontal position.

  Make sure the log splitter is secured in the horizontal position before moving the log splitter.  

DO NOT move the log splitter when it is in the vertical position because it will be unstable and could tip.

 

 

Hills.

  Do not move the log splitter up or down hills by hand – use a towing vehicle.

 

 

Engine off.

  Never move the log splitter with its engine running.

 

 

No riding.

  Never allow anyone to sit or ride on the log splitter.

 

 

No cargo.

  Never transport cargo or wood on the log splitter.

 

 

Safety During Towing 

 

Read instructions.

  Review towing safety instructions in your towing vehicle manual.

 

 

Securely attached.

  Be sure the log splitter is securely attached to the towing vehicle before towing.

 

WARNING 

Carefully read and make sure you understand the following safety information before using the log splitter. 

Improper use or maintenance of the log splitter can result in serious injury to the operator or 
bystanders from moving parts that can crush or cut, flying objects, escaping high pressure hydraulic 
fluid, or carbon monoxide poisoning.

 

Summary of Contents for M2965020D









































Reviews: