background image

For Customer Service, Call 

1-800-835-0606

 

ext. 205

or Visit 

www.doughXpress.com

TXM-20

Manual Dough Press

70612 RV D 040715

OWNER’S MANUAL

Receiving & Setup ............................................................................................2

Operation ..........................................................................................................3

Setting Temperature & Time .............................................................................4

Preference Settings ..........................................................................................5

Machine Presets ............................................................................................6-7

Cycle Count ......................................................................................................8

Temperature & Time Modes .............................................................................9

Pressing Dough .........................................................................................10-11

Dough Weights & Shrinkage ..........................................................................12

FAQs...............................................................................................................13

Troubleshooting ..............................................................................................14

Cleaning & Maintenance ................................................................................15

Warranty .........................................................................................................16

CONTENTS

BEFORE warranty repair you MUST get Prior Authorization:

Summary of Contents for TXM-20

















Reviews: