background image

SAFETY  CHECKLIST

1.

Before operating the compressor, ensure the vessel to

which the compressor is connected is certified to with-
stand the pressure and /or vacuum produced.

2.

Verify adequately sized relief valves (if necessary, CE

approved) have been fitted to protect the vessel.

3.

Gas/air mixtures which are potentially volatile/explosive

must not be introduced or allowed to be introduced into
the compressor.

4.

All pressure vessel and piping connected to the compres-

sor must be isolated and in a safe operating condition.

5.

Operators should wear ear protection when operating

truck mounted compressors.

6.

There are components within the compressor of sufficient

weight to cause injury if mishandled. Use proper lifting
devices as necessary.

7.

Where necessary, this equipment should be grounded to

control static electricity.

8.

The temperature of the air leaving the compressor is ele-

vated above ambient due to air compression. Check that
the elevated temperatures do not adversely affect the
product and any material used in design of the system.
Attach clearly marked warning signs to warn of potential-
ly hot surfaces on the compressor, piping and accessories
which will burn if touched.

9.

Mounting of the compressor must be correctly engineered

and the compressor must be properly secured. Refer to
the Compressor Mounting section of this manual. In par-
ticular, the installation shall be done in such a way that no
rotary part may be touched by the operator in normal
operation.

NOTICE :

BLACKMER COMPRESSORS ARE NOT DESIGNED FOR HANDLING
LIQUID, POWDER OR CONDENSATE.
TO DO SO WILL VOID THE WARRANTY.

CONTENTS OF THE COMPRESSOR,
TANK, PIPING, AND FILTERS COULD BE
HAZARDOUS TO HEALTH. TAKE ALL
NECESSARY PRECAUTIONS WHEN PER-
FORMING COMPRESSOR SERVICE OR
MAINTENANCE.

WARNING

Hazardous or toxic

fluids can cause

serious injury.

COMPRESSOR, PIPING AND ACCESSO-
RIES WILL BECOME HOT DURING OPERA-
TION AND CAN CAUSE SERIOUS PERSO-
NAL INJURY.

CAUTION

Extreme heat can

cause injury or

property damage.

FAILURE TO INSTALLADEQUATELY SIZED
PRESSURE RELIEF VALVE(S) CAN CAUSE
PROPERTY DAMAGE, PERSONAL INJURY
OR DEATH.

CAUTION

Hazardous pressure 

can cause 

personal injury 

or property damage.

COMPRESSING GASES INTO A VESSEL
CONTAINING FLAMMABLE OR EXPLOSI-
VE GASES, OR COMPRESSING FLAMMA-
BLE OR EXPLOSIVE GASES, CAN CAUSE
PROPERTY DAMAGE, PERSONAL INJURY
OR DEATH.

WARNING

Hazardous fluids 

can cause fire,

serious personal 

injury or property

damage.

IT IS IMPERATIVE TO APPLY THE TRUCK
PARKING BRAKE AND TO BLOCK THE
WHEELS BEFORE ANY INTERVENTION
DUE TO RISKS OF SERIOUS BODILY INJU-
RIES OR PROPERTY DAMAGE.

WARNING

Hazardous machinery can

cause severe 

personal injury or 

property damage 

3/21

NT 1401-F00 12.05 Cold front outlet Intercooler TYPHON e

S

SA

AFFE

ET

TY

Y  D

DA

AT

TA

A

Summary of Contents for Blackmer TYPHON 1000






















Reviews: