background image

6          

888-994-7636

 

the unlimited number of customer related circumstances that can cause 
gasket  failure  all  gasket  replacement  issues  are  considered  non-
warranty.    Unified  Brands  recommends  thorough  cleaning  of  gaskets 
on a weekly basis with a mild dish soap and warm water.  With proper 
care  Randell  gaskets  can  last  up  to  two  years,  at  which  time  we 
recommend  replacement  of  all  gaskets  on  the  equipment  for  the  best 
possible performance. 

 

NOTICE:  FOOD LOSS IS NOT COVERED UNDER WARRANTY  

 

3.  Repairs  caused  by  abuse  such  as  broken  glass,  freight  damage,  or 

scratches and dents. 

4.  Electrical  component  failure  due  to  water  damage  from  cleaning 

procedures. 

 
QUOTATIONS 
Verbal  quotations  are  provided  for  customer  convenience  only  and  are 
considered  invalid  in  the  absence  of  a  written  quotation.    Written  quotations 
from  Unified  Brands  are  valid  for  30  days  from  quote  date  unless  otherwise 
specified.    Unified  Brands  assumes  no  liability  for  dealer  quotations  to  end-
users. 
 
SPECIFICATION & PRODUCT DESIGN 
Due to continued product improvement, specification and product design may 
change  without  notice.    Such  revisions  do  not  entitle  the  buyer  to  additions.  
Changes or replacements for previously purchased equipment. 
 
SANITATION REQUIREMENTS 
Certain  areas  require  specific  annotation  requirements  other  than  N.S.F.  & 
U.L. standards.  Unified Brands must be advised of these specifications before 
fabrication of equipment.  In these special circumstances, a revised quotation 
may  be  required  to  cover  additional  costs.    Failure  to  notify  Unified  Brands 
before fabrication holds the dealer accountable for all additional charges. 
 
CANCELLATIONS 
Orders 

canceled 

prior 

to 

production 

scheduling 

entered 

into 

engineering/production  and  cancelled  are  subject  to  a  cancellation  charge 
(contact factory for details). 
 
STORAGE CHARGES 
Unified  Brands  makes  every  effort  to  consistently  meet  our  customer’s 
shipment  expectations.    If  after  the  equipment  has  been  fabricated,  the 
customer requests delay in shipment, and warehousing is required: 
 

2.  Equipment  held for  shipment  at  purchasers  request for  a  period  of  30 

days  beyond  original  delivery  date  specified  will  be  invoiced  and 
become immediately payable. 

3.  Equipment  held  beyond  30  days  after  the  original  delivery  date 

specified will also include storage charges. 

 
SHIPPING & DELIVERY 
Unified  Brands  will  attempt  to  comply  with  any  shipping,  routing  or  carrier 
request  designated  by  dealer,  but  reserves  the  right  to  ship  merchandise  via 
any  responsible  carrier  at  the  time  equipment  is  ready  for  shipment.    Unified 

Summary of Contents for Unified Brands Randell PH120F




























Reviews: