08/09/16
FIG. 8
.125
(1/8")
Vertical Adjustment
Locking Screw
Mounting Screw
Horizontal Adjustment
Locking Screws
Both Sides
Keeper
Mounting Screw
SHEET 3 OF 3
GATE
POST
GATE
POST
FRONT
template
FIG. 8
.125
(1/8")
Vertical Adjustment
Locking Screw
Mounting Screw
Horizontal Adjustment
Locking Screws
Both Sides
Keeper
Mounting Screw
SHEET 3 OF 3
GATE
POST
GATE
POST
FIG. 8
.125
(1/8")
Vertical Adjustment
Locking Screw
Mounting Screw
Horizontal Adjustment
Locking Screws
Both Sides
Keeper
Mounting Screw
SHEET 3 OF 3
GATE
POST
GATE
POST
Keeper
FIG. 8
.125
(1/8")
Vertical Adjustment
Locking Screw
Mounting Screw
Horizontal Adjustment
Locking Screws
Both Sides
Keeper
Mounting Screw
SHEET 3 OF 3
GATE
POST
GATE
POST
Mount
Mark Latch
position
on SIDE
of gate
To change the
Latch for
left-handed
install.
Slide Keeper
off the
Mount and
rotate it
180° degrees.
Slide bottom cover
out of Latch.
Slide it into the top.
Use both FRONT and
BACK templates to mark
the mounting holes.
Drill a Ø19mm hole at
the centre (marked 3/4”)
on the both
templates.
Drill the Ø3mm pilot
holes (marked 1/8”)
at each corner of the
template.
LEFT
CENTERLINE
OF LATCH
3/4"
SPINDLE
THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
12mm
Screw
30mm
Screw
Trim Spindle Tube 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
RIGHT
CENTERLINE OF LATCH
3/4"
SPINDLE THRU HOLE
GATE FRAME
3/4"
FIG. 1
12mm
Screw
30mm
Screw
Trim Spindle Tube 11-13mm Longer than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be 11 to 13mm longer than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
The Latch comes ready
for Right-Handed gates. A
few simple steps and the
Latch is ready for
Left-Handed gates.
CENTERLINE
OF LATCH
3/4"
SPINDLE THRU
HOLE
GATE
FRAME
3/4"
FIG. 1
12mm
Screw
30mm
Screw
Trim Spindle Tube 11-13mm
Longer than Gate Post
Spindle Tube
MUST be fitted
Spindle Tube to be
11 to 13mm longer
than Gate Post
Spindle
INSIDE
LATCH
OUTSIDE
LATCH
CENTERLINE OF LATCH
3/4"
SPINDLE THRU HOLE
GATE FRAME
3/4"
FIG. 1
12mm
Screw
30mm
Screw
Trim Spindle Tube 11-13mm Longer than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be 11 to 13mm longer than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
CENTERLINE OF LATCH
3/4"
SPINDLE THRU HOLE
GATE FRAME
3/4"
FIG. 1
12mm
Screw
30mm
Screw
Trim Spindle Tube 11-13mm Longer than Gate Post
Spindle Tube MUST be fitted
Spindle Tube to be 11 to 13mm longer than Gate Post
Spindle
INSIDE LATCH
OUTSIDE LATCH
Left or
Right?
START
MAGNET
LEVER
LATCH
- Suits 40 - 125mm Posts
- Left or Right Handed
- Single or Double Gates
- Lock/Unlock Both Sides
DPLLEVER
FIG. 8
.125
(1/8")
Vertical Adjustment
Locking Screw
Mounting Screw
Horizontal Adjustment
Locking Screws
Both Sides
Keeper
Mounting Screw
SHEET 3 OF 3
GATE
POST
GATE
POST
GATE
POST
POST
GATE
MAGNET
LEVER
LATCH
- Suits 40 - 125mm Posts
- Left or Right Handed
- Single or Double Gates
- Lock/Unlock Both Sides
DPLLEVER
MAGNET
LEVER
LATCH
- Suits 40 - 125mm Posts
- Left or Right Handed
- Single or Double Gates
- Lock/Unlock Both Sides
DPLLEVER
