A-7
USER OPERATION INSTRUCTION
WARNING
THE SURFACE ABOVE THE BAKING CHAMBER OPENINGS ARE EXTREMELY HOT
AND CAN CAUSE SERIOUS INJURIES
“This appliance is only for professional use and should be used by qualified persons only"
1.
Open the main gas valve.
2.
Turn on the ventilation system if necessary.
3.
Turn the switches to the position "ON" (turn on both switches, "main switch" and "oven start
switch"). See page A9 or A10 for operation description.
•
The green light "READY FOR OPERATION" must turn on for a few seconds (it
indicates that every starting condition is present)
•
The blower starts and the burner fires if the thermostat is adjusted over the ambient
temperature (the green light "BURNER" indicates that the burner is fired).
(If nothing happened, press the breakers on the front)
4.
Adjust the thermostat at the desired setting (see THERMOSTAT INSTRUCTIONS bellow).
5.
Wait until the unit reaches the baking temperature (see tables "Pizza baking time").
•
When the desired temperature is reached, the red light (on the thermostat) goes out
and turns green then the burner stops.
6.
Adjust baking time according to your product (see suggestions “Pizza baking time”).
Use the arrows up/down on the micro drive.
7.
Place your products on the conveyor.
Use a screen for a regular pizza and use pan for a pan pizza.
IMPORTANT:
To stop the oven, turn the "oven start switch" to the position "OFF
"( the blower will run for
15 minutes and temperature will decrease quickly to avoid electronic components to get too hot).
Use the red emergency switch only in case of an emergency.
POWER FAILURE
The burner, the electric gas valve and the regulator are all designed to be fail safe. Then, there is
no special action to take in case of electrical power failure. Turn off the oven. Never leave the
oven unsupervised when the power is on the unit.
THERMOSTAT INSTRUCTIONS
The temperature of the oven is always shown on the display of the thermostat and an arrow
indicates if the temperature is over the SP (set point) or below. When the green light is lit, it
indicates that the temperature is at the SP ± 1 %.
Summary of Contents for FC18GEU
