A8
OPERATION OF THE OVEN
1.
Turn the switch to the " ON " position.
•
The light inside the oven must light up.
2.
Adjust the thermostat at the desired setting (see THERMOSTAT INSTRUCTIONS below).
N.B. The red light must be "ON" (If not, press the breaker on the front).
3.
Heat the unit until you reach the baking temperature.
When the desired temperature is reached, the red light goes out and turns green.
If the light is still "ON" and the oven does not produce heat, call for service.
4.
Load the oven as fast as possible to avoid letting out too much heat.
5.
Set the timer to the desired value and start it. (see "TIMER" adjustment on next page)
NOTE:
The timer does not shut the oven off at the end of its cycle. It simply activates the buzzer.
6.
Wait until the product is ready. Do not open the doors until the product is done.
VERY IMPORTANT
This oven has an overheat warning alarm to protect the electrical components against overheating. If
the red pilot light (OVERHEAT WARNING) is lit and you hear a buzzer, see troubleshooting.
THERMOSTAT INSTRUCTIONS
To obtain a very good thermal stability, we use a digital temperature controller with thermocouple.
The Omron E5CS thermostat controls the heat of every element at the SP (set point).
The temperature of the oven is always shown on the display of the thermostat and an arrow indicates
if the temperature is over or below the SP. When the green light is lit, it indicates that the temperature
is at the SP ± 1 %.
To adjust the SP (set point) value, you just have to press the key on the left and use the up and down
keys to set the temperature. Press the left key to return to run mode.
STEAM TIMER H3DE (OPTIONAL)
VERY IMPORTANT
Steam injection will only work when the ventilator of the oven is working.
To inject steam in the oven, press and release the
STEAM TIMER
button. The light comes on
inside the steam button during the steam injection. Steam injection has been factory preset. To have
more steam, press steam button a second time, after the light is off.
P.S.
Do not inject steam more than once each time you bake. Wait at least 10 minutes before re-
timing the steam injection system.
Summary of Contents for PIZ3
