STEREO
ZONE
CABLE REF. W-2
MINIMUM SECTION
2X0.50 MM
Speaker
Ref. SP 5
STEREO
ZONE
CABLE REF. W-2
MINIMUM SECTION
2X0.50 MM
Speaker
Ref. SP 5
WIRING DIAGRAM FOR S 400 CONTROL
MODULE AND UC 400 S CENTRAL UNIT
S o u n d & H o m e
A u t o m a t i o n
CONTROL
MODULE
S 400
Technical characteristics
Nr. of channels...................................4 mono channel
Amplifier..............................................1.5+1.5W stereo
Minimum load impedance................8 ohms
Power supply......................................12Vcc/330mA
Stand-by power consumption........25mA
Operational power consumption..69mA
Connectors.........................................Strip terminals
Dimensions.........................................44 x 44 x 36mm depth
S 400
VOLUME.
AUXILIARY AUDIO INPUT
ON/OFF KEY
ALARM CLOCK AND
PARENT FUNCTION
MENU KEY
S 400
USER MANUAL
HOW TO SWITCH ON AND OFF THE CONTROL
MODULE: Press the control module on/off key. The display
will light up and either the audio program or the time will
be shown on it. Press again the on/off key to switch the
control module off.
GENERAL SYSTEM ON/OFF: Pressing simultaneously the
on/off and > keys all the control modules of the multiroom
system will switch on while a flashing “ON” will be shown
on the display.
Pressing simultaneously the on/off and < keys all the control
modules of the multiroom system will switch off while a
flashing “OFF” will be shown on the display.
CHANNEL AND AUXILIARY AUDIO INPUT SELECTOR
Push the CH key to change the audio program. The selected
channel will show on the display.
VOLUME CONTROL: While the control module is on
press the > key to turn the volume up and the < key to
turn the volume down.
CONTROL OF BALANCE AND MONO/STEREO
SOUND
While the control module is on, press repeatedly the MOD
key until the feature you want to adjust is shown on the
display. Then use the keys < and > to regulate the function.
TIME SETUP: Either when the control module is on or
off, press repeatedly the MOD key until the function “SET”
is shown on the display. Set the time using the < > keys.
Once the time is set in one module, the rest of control
modules will automatically be sincronized.
AUTO OFF SETUP: While the control module is on, press
repeatedly the MOD key until the “AUTO OFF” function
is shown on the display. The time countdown for automatic
desconexion will set by pressing the on/off key repeatedly
(time will increase in intervals of 15 minutes) or using the
< > keys (time will increase in intervals of 1 minute).
AUTO ON SETUP: While the control module is off, keep
pressed the on/off key until the “AUTO ON” function is
shown on the display. The time countdown for automatic
conexion will set by pressing the on/off key repeatedly
(time will increase in intervals of 15 minutes) or using the
< > keys (time will increase in intervals of 1 minute).
SLEEP MODE: While the control module is on, press
repeatedly the MOD key until the function “SLEEP” is
shown on the display. The switch off time can be set by
pressing the on/off key repeatedly (time will increase in
intervals of 15 minutes) or using the < > keys (time will
increase in intervals of 1 minute).
Another way to activate this function is by keeping pressed
the on/off key during 3 seconds while the control module
is on. When the “SLEEP” mode is shown on the display, the
switch off time can be set by pressing the on/off key
repeatedly (time will increase in intervals of 15 minutes)
or using the < > keys (time will increase in intervals of 1
minute).
ALARM CLOCK SETUP: Either when the control module
is on or off, press repeatedly the MOD key until the
“ALARM” function is shown on the display. Using the < >
keys the alarm time can be set. Immediately after the alarm
mode (CH1, IN or BEEP) can be chosen by pressing the
alarm clock key on the right hand side. The alarm clock
volume can be also preset using the < > keys. A small bell
symbol on the display will show the alarm clock is on.
To switch off the alarm clock when ringing just press any
key.
To deactivate the alarm clock function press repeatedly
the MOD key until the “ALARM” function is shown on the
display. Immediately after press repeatedly the alarm clock
key on the right hand side until “ALARM OFF” is shown
on the display. The bell symbol will not appear on the display
any more.
The control module memorizes the last alarm clock setting
if no new features are introduced.
CALL RECEPTION AND BABY-PHONE LISTENER
Either when the control module is on or off, calls from
built-in microphone control modules can be received. The
zone number of the zone that is calling will show on the
display “CALL IN + NR”.
The S 400 can be activated as a listener control module
in the baby-phone function. After having activated the
control module in the children’s bedroom (this must be a
built-in microphone control module) press twice the MOD
key in the listener control when the module is off. “PARENT”
will show on the display. Use the < > keys to activate or
deactivate the listening function.
Up to 5 baby rooms and 5 listening areas can be selected
to be working simultaneously.
The listening volume can be adjusted using the < > keys,
is independent from the program volume and is automatically
memorized by the control module.
DO NOT DISTURB MODE: When the control module
is on, press repeatedly the MOD key until “DONT
DISTURB:OFF” is shown on the display. Press the > key
to activate the “do not disturb” function. DONT
DISTURB:ON” will be shown on the display. From that
moment the control module will not receive any call.
To deactivate this function, repeat the operation and press
the key <. “DONT DISTURB:OFF” will be shown on the
display and from that moment the “do not disturb” mode
will be deactivated.
AUXILIARY AUDIO INPUT (IN): Connect the audio player
jack in the audio socket. Press the auxiliary audio input key
until “IN” is shown on the display.
LCD DISPLAY
CHANNEL AND AUX. IN
SELECTOR
RED 230 Vca.
2x0,75 mm.
0
5
8
9
-
+
+
-
ANT
C1L
C1R
R+ R- L- L+
C2L
C2R
C3L
C3R
C4L
C4R
S 400
UC 400 S
0
5
-
+
+
-
ANT
R+ R- L- L+
S 400
0 5 8 9
0 5 8 9
C1 C2 C3 C4
C1 C2 C3 C4
M
M
M
www.doyson.com
NOTE.-
The
UC 400 S
supports a máximum of 10 sound control modules and a maximum distance of 100 mts.of cable to the last
element to be controlled. For higher installations, power supply units or a more powerful central unit would be required.
HOW TO PROGRAM THE SYSTEM:
Once all the system units are already installed, a zone number must be assigned to each control module as follows:
1st.- Keep the keys <> pressed during 4 seconds. The number “1” will be shown on the displays of ever y control module.
2nd.- Choose the control module you want to be the “zone 1” and press the On/Off key. The number “1” will be memorized as a zone number in
that control module.
3rd.- Now the rest of control modules will show the number “2” in their displays. Choose again which control module you want to be the “zone 2”
and press the On/Off key of that module.
4th- Repeat the process as many times as control modules/zones are in the installation.
5th- Once the zone assignment is finished, keep the control module on/off key pressed during 4 secondsin order to leave the “assingnment zone mode”.
CABLE REF. W-14
MINIMUM SECTION
2X1MM
12X0,25 MM
0
5
8
9
C1
C2
C3
C4
GROUND - Vcc
POWER SUPPLY 12 +Vcc
COMMUNICATIONS
COMMUNICATIONS
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
=
=
=
=
=
=
=
=
System with power supply unit
System with central unit
For AUXILIARY CONNECTION of audio, TV, PC, etc. please
use 0 (ground) and C1
ANTENNA CONNECTION:
Conductor wire of 80 cm. In zones of
bad reception, connection to outdoor antenna it is highly recommended.
FA 12 BI
Power supply
unit
