background image

 

 

DR

®

 

2-CYCLE TILLER CULTIVATOR

 

 

2-Year Limited Warranty 

 

Terms and Conditions 

The DR

 2-CYCLE  TILLER CULTIVATOR is warranted for two (2) years against defects in materials or workmanship 

when put to ordinary and normal consumer use; ninety (90) days for any other use. 

For  the  purposes  of  all  the  above  warranties,  “ordinary  and  normal  consumer  use”  refers  to  non-commercial 
residential use and does not include misuse, accidents or damage due to inadequate maintenance. 

DR  Power  Equipment  certifies  that  the  DR

  2-CYCLE  TILLER  CULTIVATOR  is  fit  for  ordinary  purposes  for  which  a 

product of this type is used. DR Power Equipment however, limits the implied warranties of merchantability and fitness 
in duration to a period of two (2) years in consumer use, ninety (90) days for any other use.

 

The 2-Year Limited Warranty on the DR

 2-CYCLE TILLER CULTIVATOR starts on the date the machine ships from our 

factory. The 2-Year Limited Warranty is applicable only to the original owner. 

The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's 
owner's manuals. The warranty holder is responsible for replacement of normally wearing parts such as the Tines, Tine 
Hardware,  Throttle  Lever,  Spark  Plug,  Air  Filter,  and  Wheels.  Attachments  and  accessories  to  the  machine  are  not 
covered by this warranty. 

During  the  warranty  period,  the  warranty  holder  is  responsible  for  the  machine  transportation  charges,  if  required. 
During the warranty period, warranty parts will be shipped by standard method at no charge to the warranty holder. 
Expedited shipping of warranty parts is the responsibility of the warranty holder. 

SOME  STATES  DO  NOT  ALLOW  LIMITATIONS  ON  THE  LENGTH  OF  IMPLIED  WARRANTIES,  SO  THE  ABOVE 
LIMITATIONS MAY NOT APPLY TO YOU.

 

DR  Power  Equipment  shall  not  be  liable  under  any  circumstances  for  any  incidental  or  consequential  damages  or 
expenses of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to 
perform tasks normally performed by the DR

 2-CYCLE TILLER CULTIVATOR. 

SOME  STATES  DO  NOT  ALLOW  THE  EXCLUSION  OR  LIMITATION  OF  INCIDENTAL  OR  CONSEQUENTIAL 
DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 

THIS  WARRANTY  GIVES  YOU  SPECIFIC  LEGAL  RIGHTS,  AND  YOU  ALSO  HAVE  OTHER  RIGHTS,  WHICH  VARY 
FROM STATE TO STATE. 

Summary of Contents for PILOT 2C





















Reviews: