background image

 

 

display, the batteries should be replaced immediately.   

10. Cleaning and Disinfecting   

Use an alcohol swab or cotton tissue moistened with alcohol (70% Isopropyl) 

to clean the thermometer casing and the measuring probe. Ensure that no liquid 

enters the interior of the thermometer. Never use abrasive cleaning agents, thin-

ners or benzene for cleaning and never immerse the instrument in water or other 

cleaning liquids. Take care not to scratch the surface of the probe lens and the 

display.   

11. Battery Replacement   

This instrument is supplied with 2 new, long-lives 1.5V, size AAA batteries. 

Batteries need replacing when this icon « »

24

  is the only symbol shown on the 

display. Use a screwdriver to open the battery cover. Replace the batteries – 

ensure correct polarity as shown by the symbols in the compartment. 

Batteries and electronic instruments must be disposed of in accordance 

with the locally applicable regulations, not with domestic waste.   

 

 

12. Technical Specifications 

Type: Non-Contact Thermometer FR200 

Measurement Range: Body Mode: 34.0-42.2  °C (93.2-108.0  °F) 

Object Mode: 0-100.0  °C (32-212.0  °F) 

Resolution: 0.1  °C /  °F 

Measurement Laboratory:  ±0.2  °C, 36.0~39.0  °C 

Accuracy:(±0.4  °F, 96.8~102.2  °F)   

Display: Liquid Crystal Display, 4 digits plus special 

Acoustic: The unit is turned ON and ready for the measurement: 1 short beep Complete the 

measurement:1 long beep (1 sec.) if the reading is less than 37.5  °C (99.5  °F), 10 short 

«beep», if the reading is equal to or greater System error or malfunction:3 short «bi» sounds 

Memory: 

Auto-Display the last measured

 

temperature30 readings recall in the Memory 

Mode 

Backlight: 

The display light will be GREEN for 4 seconds, when the unit is turned ON. The 

display light will be GREEN for 5 seconds, when a measurement is completed with reading 

equal to or lower than 37.5  °C(99.5  °F).The display light will be RED for 5 seconds, when a 

measurement is completed with a reading higher than 37.5  °C(99.5  °F). 

Operating: Body Mode: 16-40.0  °C (60.8-104.0  °F) 

Temperature: Object Mode: 5-40.0  °C (41-104.0  °F) icons   
Storage:-20  °C to +50  °C (-4  °F to 122  °F) 
Temperature:    15-95 % relative 
maximum humidity   
Automatic:Approx. 1 minute after last measurement   

Summary of Contents for FR200











Reviews: