background image

4

         

D R

®  

HORIZONTAL/VERTICAL LOG SPLITTER

 

Operating this Log Splitter safely is necessary to prevent or minimize the risk of death or serious injury.  Unsafe operation can 
create a number of hazards for you.  Always take the following precautions when operating this Log Splitter: 

 

Always wear protective goggles or safety glasses with side shields while using the Log Splitter to protect your eyes from 
possible thrown debris. 

 

Avoid wearing loose clothing or jewelry, which can catch on moving parts. 

 

We recommend wearing gloves while using the Log Splitter.  Be sure your gloves fit properly and do not have loose cuffs or 
drawstrings. 

 

Wear shoes with non-slip treads when using your Log Splitter.  If you have safety shoes, we recommend wearing them.  Do 
not use the machine while barefoot or wearing open toed sandals. 

 

Wear long pants while operating the Log Splitter. 

 

Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing. 

Protecting Yourself and Those Around You 

Safety for Children and Pets 

Hydraulic Safety 

Tragic accidents can occur if the operator is not alert to the presence of children and pets.  Children are often attracted to the 
machine and the splitting activity.  

Never assume that children will remain where you last saw them.  Always follow these 

precautions:

 

 

Keep children and pets at least 50 feet from the working area and ensure they are under the watchful care of a responsible 
adult. 

 

Be alert and turn the machine off if children or pets enter the work area. 

 

Never allow children to operate the Log Splitter.

 

High fluid pressures are developed in hydraulic machines. Pressurized hydraulic fluid escaping through a pin hole opening can 
puncture skin and cause severe blood poisoning. Therefore, the following Instructions should be heeded at all times. 

 

Do not operate the unit with frayed, kinked, cracked or damaged hoses, fittings, or tubing. Stop the engine, wait 5 minutes 
and relieve hydraulic system pressure 

by cycling the valve control lever from forward to reverse several times and returning to 

neutral while engine is not running

 before changing or adjusting fittings, hoses, tubing, or other system components. 

 

Do not change any Log Splitter relief valve settings. They are set at the factory for best Splitter performance and safety. 

 

Do not check for leaks with your hand. Leaks can be located by passing cardboard or wood over the suspected area: Look for 
discoloration. If injured by escaping fluid, see a doctor at once. Serious infection or reaction can develop if proper medical 
treatment is not administered immediately. 

 

Always wear safety glasses to protect your eyes from hydraulic fluid. 

 

NEVER remove the cap from the hydraulic tank or reservoir while the log splitter is running. The tank could contain hot oil 
under pressure which could result in serious injury. 

 

This machine was built to be operated according to the safe operation practices in this manual. As with any type of power 
equipment, carelessness or error on the part of the operator can result in serious injury. This machine is capable of 
amputating hands and feet and throwing debris. Failure to observe the following safety instructions could result in serious 
injury or death. 

 

Many accidents occur when more than one person operates the machine. No helper is allowed to assist with splitter controls 
or handling the logs. 

Summary of Contents for 22-Ton





































Reviews: