background image

中龙集团

Dragon Group China Limited 

                                                                                       

                             

                                     

BIRD

®

 

 

                                         
 

 

www.dragongroupchina.com

   

www.chinaemall.biz

 

 

Generally, before mounting a new BGA, the paste should be laid on the pad with a 

special micro mesh. But for those common devices such as PBGA or MBGA, the paste 

can  be  laid  on  the  pad  directly,  and  the  soldering  can  be  finished  by  the  melting  of 

soldering balls. Of course, for CBGA, a mesh and soldering paste are necessary, because 

the melting point of soldering balls on CBGA is much higher than common paste, such as 

Sn63 and pb27.   

4. Removal of residual soldering tin and mounting of BGA   

Besides the temperature curve, the removal of remained soldering tin and mounting 

of BGA are of great importance in BGA rework. Generally, people don't realize it. But in 

practice, it often leads to failure in BGA rework.   

We usually use copper tin-absorption line to remove the residual tin. In the rework 

process, the pad is likely  to be destroyed by the wrong operation of the technician, thus 

the  total  process  of  BGA  rework  becomes  a  failure.  Therefore,  we  should  pay  more 

attention.  Here  are  2  tips:  one  is  to  remove  the  residual  tin  within  a  short  time  after 

desoldering  BGA.  Because  at  that  time  PCB  has  not  cooled  down  completely  and  the 

temperature  difference  cause  less  damage  to  the  pad;  the  other  tip  is  to  use  some  flux 

when  removing  the  residual  soldering  tin,  which  can  improve  the  activity  of  tin.  Never 

move  the  copper  tin-absorption  line  under  the  great  pressure  of  soldering  iron.  The 

remounting of BGA calls for the "fine finish" of tin removal. Thus it ought to be operated 

by some experienced technicians.   

5. Use of nozzle   

Every  hot-air  heating  rework  station  need  a  suitable  nozzle.  It  is  better  to  use  a 

nozzle which is 2-5mm bigger than the component, then the component is entirely   

covered by the nozzle, and BGA can be heated evenly.   

 

 

Summary of Contents for Bird AC-5K

































Reviews:

Related manuals for Bird AC-5K