background image

Battle Born Batteries 

BB10012/H

 Manual 

How to Incorporate Fuses into System Install

 

ANL fuses are designed to melt and separate into two pieces for the purpose of breaking a circuit in the 
event of excessive current. These fuses are essential components for protecting against a catastrophic 
event and are found through the DC and are typically placed between Battle Born Batteries and the 
inverter/load. 

How to Properly Store Batteries

 

We recommend bringing the Battle Born Batteries to a 100% state of charge. Then, disconnect the 
battery from any loads by removing the negative cable from one battery. On average, the batteries lose 
approximately 2-3% capacity per month. This is subject to increasing if stored in extreme environmental 
conditions. 

How to Maintain the Batteries

 

Battle Born Batteries require very little maintenance. If your batteries are in series and not being 
charged by a multi-bank charger it is recommended that you fully charge the batteries individually once 
every three months if the system is used frequently. This will internally balance your batteries to 
ensure that they will reach their expected life span and allow you to get the full power out of them with 
each use. If your batteries are in parallel this is not necessary, just make sure the batteries are charged 
to 14.2V – 14.6V frequently for internal balance. Our BMS has a built-in passive balancing system that 
will take care of this for you. 

For more FAQs scan the QR code. 

Fuse QR Code

 

Storage QR Code

 

FAQ QR Code

 

Warranty

 

Dragonfly Energy Corp. (“the Manufacturer”) warrants each Dragonfly Energy and Battle Born Batteries branded Li-ion battery (“the 
Product”) sold by Dragonfly Energy, Battle Born Batteries, or any of its authorized distributors or dealers, to be free of defects for a 
period of 10 years (“the Warranty Period”) from the date of sale as determined by either the customer’s sale receipt, the shipping 
invoice, and the battery serial number, with proof of purchase. Within the first 8 years of the Warranty Period, subject to the 
exclusions listed below, the Manufacturer will credit, replace, or repair, if serviceable, the Product and/or parts of the Product if the 
components in question are determined to be defective in material or workmanship. After 8 years and up to 10 years, if the 
components in question are determined to be defective in material or workmanship, and the Manufacturer deems the components 
to be repairable, the Product will be repaired and returned. If the Manufacturer deems the components to be not repairable, a new, 
similar Product will be offered at a discount of 30% off the price listed at the time of the offer. The offer will be valid for a period of 
30 days after the date of notification. Se

https://battlebornbatteries.com/terms-conditions/#warranty 

for the full warranty policy. 

NON-TRANSFERABLE

 

This Limited Warranty is to the original purchaser of the Product and is not transferable to any other person or entity. Please contact 
the place of purchase regarding any warranty claim. 

WARRANTY EXCLUSIONS

 

The Manufacturer has no obligation under this Limited Warranty for Product subjected to the following conditions (including b

ut 

not 

limited to

): 

 

Damage due to improper installation; loose terminal connections, under-sized cabling, incorrect connections (series and

parallel) for desired voltage and AH requirements, or reverse polarity connections.

Environmental damage: inappropriate storage conditions as defined by the Manufacturer; exposure to extreme hot or cold

temperatures, fire or freezing, or water damage.

Damage caused by collision.

Damage due to improper maintenance, under or over-charging the Product, dirty terminal connections.

Summary of Contents for Battle Born BB10012









Reviews: