Draper 13064 User Manual Download

Page: 11 / 12

- 11 -

9. TROUBLESHOOTING

9.1 TROUBLESHOOTING

Release valve may not be tightly closed.
Jack may be low on oil. Remove filler plug and fill reservoir

with clean hydraulic jack oil.
Reservoir may be overfilled. Remove filler plug and drain

excess oil.
Jack may be air-bound. Bleed pump as per “before use”

section of this manual. Close the release valve and operate.

Repeat if necessary.
Valves may not be closed or have foreign matter present. To

flush valves. Lower the saddle and close the release valve.

Manually lift the saddle several inches, open the release

valve and then force the saddle to lower as rapidly as

possible.

Jack will not lift full height.

Handle raises or flies

back under load.

Pump feels spongy

Oil leaking from filler plug.

Jack lowers under load.

Jack won't lift load or

full rated capacity

Problem

Troubleshooting

Check List

Summary of Contents for 13064













Search results

Summary of Contents for 13064

Reviews:

Related manuals for 13064

Brands by name

Popular brands

Draper 13064, User Manual

Search results

Summary of Contents for 13064

Reviews:

Related manuals for 13064

Brands by name

Popular brands