Section 1 -
Idler-End and Operator End Assemblies
Please Note:
The operator will already be installed in the operator-end roller; the sliding pin idler will also be installed in the idler-end roller. It is only necessary to
install the coupler assemblies.
Section 1.1 - 2"
(51 mm)
Idler-End Assembly
Please Note:
Notches in the tube need to be lined up with the "keys" on the
couplers.
1.
Insert coupler assembly into roller. Making sure the notch in the tube is lined
up with the "key" on the coupler, press until the assembly is fully seated in
the roller.
Caution:
•
Ensure the locking ring on the idler-end coupler assembly is fully tightened
before installing roller into brackets. There should be no play in the locking
ring. If the locking ring is loose, then the idler is in "height adjustment"
mode.
•
Wear a heavy glove on the hand used to grip the locking ring.
•
Tighten the locking ring until it is fully locked and it cannot rotate any
further. Check to ensure it is tight and will not work loose. If locking ring
cannot be tightened by hand, use a flat screwdriver or other tool to assist.
Section 1.2 - 2"
(51 mm)
Operator-End Assembly
Please Note:
Operator-end coupler assemblies will not slide straight in to the
roller tube.
1.
Insert assembly into the roller, with the "key" slightly off center from the
notch.
2.
Once assembly is far enough in that the ribs are past end of the notch, rotate
the coupler until the notch is lined up with the "key" on the coupler.
Please Note:
If the assembly will not fully seat in the roller, retract the shaft
(if applicable)
and tap the assembly with a rubber mallet. Be careful not to
damage the coupler.
Section 1.3 - 3"
(76 mm)
Idler-End Assembly
Please Note:
The retractable shaft needs to be pointing toward
the opposite end of the motor and oriented that direction for the
whole unit.
1.
Insert coupler assembly adapter into roller. Making sure the notch
in the adapter is lined up with the notch in the coupler, press until
the adapter is fully seated in the roller.
2.
Insert coupler assembly into adapter. Making sure the notch in the
inside of the adapter is lined up with the "key" on the coupler, press
until the assembly is fully seated.
Caution:
•
Ensure the locking ring on the idler-end coupler assembly is fully
tightened before installing roller into brackets. There should be no
play in the locking ring. If the locking ring is loose, then the idler is
in "height adjustment" mode.
•
Wear a heavy glove on the hand used to grip the locking ring.
•
Tighten the locking ring until it is fully locked and it cannot rotate
any further. Check to ensure it is tight and will not work loose. If
locking ring cannot be tightened by hand, use a flat screwdriver
or other tool to assist.
Section 1.3 - 3"
(76 mm)
Operator-End Assembly
1.
Follow the same steps used for the idler-end.
Please Note:
If the assembly will not fully seat in the roller, retract
the shaft
(if applicable)
and tap the assembly with a rubber mallet. Be
careful not to damage the coupler.
OR
C177.059SA
C177.062SA
OR
C177.058SA
C177.061SA
Idler End Coupler
Operator End Coupler
C103.069
C177.061SA
AND
C103.069
C177.062SA
AND
Idler End Coupler
Operator End Coupler
Figure 1a
Figure 1b
Please Note:
The retractable shaft must point toward the opposite end of
the motor and oriented in that direction for the entire unit.
Please Note:
The retractable shaft must point toward the opposite end of
the motor and oriented in that direction for the entire unit.
page 3 of 10
Dual Roller Coupled Motorized FlexShades
®
(Standard Hardware)
