FlexShade
®
ZIP XL
page 2 of 11
Caution:
1.
Inspect all boxes to make sure you have
received the proper shades and parts.
Controls may be shipped separately, or in
same carton as shades.
2.
Open cartons lengthwise, taking care not
to cut into cardboard shipping container.
3.
Before mounting shades, verify
measurements on label provided with shade,
and ensure unit is installed at correct width.
4.
All endcaps, fascia, headbox, and other
hardware must be installed level. Shades
must be level and square.
6. Read the following installation guidelines
thoroughly and follow them carefully.
Failure to do so may cause product to fall or
otherwise fail, and invalidates warranty.
7. Installer is responsible for selecting mounting
hardware appropriate for site conditions.
PLEASE READ -
Cleaning and Maintenance
Window covering products manufactured by Draper, when properly installed, should require no operational maintenance or lubrication.
Most standard Draper fabrics may be cleaned at the window by vacuuming with a soft brush attachment. They also may be cleaned by using a sponge or soft cloth
and mild solution of warm soapy water. A mild dishwashing liquid is recommended. A clean dry cloth is recommended for the metal finish.
Please Note:
Exceptions are GreenScreen Evolve
®
, GreenScreen Revive
®
, and Phifer
®
SW7000 fabrics, which must be cleaned with a dry art sponge.
(GreenScreen Revive
®
and GreenScreen Evolve
®
are registered trademarks of Mermet
®
USA. SheerWeave
®
is a registered trademark of Phifer
®
Incorporated.)
WARNING
Improper installation and use of the FlexShade
®
ZIP XL can result in serious injury or death. Primarily, injuries can occur if the unit falls
due to imprecise installation, mishandling of the unit during installation, or installation on an insufficient wall or ceiling structure.
Please use extreme care.
1.
Please read the following installation guidelines thoroughly and follow them
carefully. Failure to do so may cause product to fall or otherwise fail, and
could result in serious injury.
2.
Installation and calibration of the unit should only be performed by an
authorized, qualified, and experienced professional. In particular, electrical
work and wiring [indicated in diagram by dashed lines] must be completed
only by a qualified professional electrician who has read this manual
completely and is familiar with the construction and operation of this
equipment and the hazards involved.
3.
Do not affix the unit to wall or ceilings that have inadequate strength to
permanently hold the unit during use. It is the owner’s and installer’s
responsibility to confirm the wall or ceiling to which the unit attaches is
sufficient to permanently hold the weight and stress loads of the unit at all
times. Draper
®
, Inc., is not responsible for improper installation, application,
testing, or workmanship related to the product at place of installation.
4.
It is the installer’s responsibility to make sure appropriate fasteners are used
for mounting.
5.
All brackets, fascia, headboxes, pockets, wall clips, and other hardware
must be installed level. Unit must be level and square.
6.
Never leave the area while operating the unit during installation,
maintenance, or normal operation, unless it is secure and safe.
7.
Before testing or operation, carefully inspect the entire area and path of the
shade and areas underneath the shade to be sure no persons or objects are
in the area.
8.
Turn off power and any nearby equipment or cables carrying electricity
before connecting switches, wires, controls, or electrical components.
9.
Make sure the limit switches are pointed down or accessible when placing
the motor in brackets/endcaps.
10.
All motors should be tested and limits set using test cord before shades
are wired.
11.
Do not wire motors in parallel without written permission from Draper, Inc.
12.
During testing or operation, carefully watch the surrounding area for any
potential safety concerns including nearby persons or objects.
13.
After installation, the entire system, including all sensors, should be carefully
tested to ensure safe and normal operation. Extreme care should be taken
during testing to remain clear of moving parts to avoid possible injury.
14.
Operation of unit should be performed only by authorized and qualified
personnel, who have been trained in the safe and effective operation of the
unit and understand its safety features.
15.
The safety features of the unit, including sensors, should never be disabled,
bypassed, or overridden. The system should not be operated until all safety
features, including the sensors, are properly and completely installed,
calibrated, and tested.
16.
Unit may need to comply with local, state, or district rules and regulations,
in particular when installed in schools. All applicable rules and regulations
should be reviewed before installation and use.
17.
Failure to precisely follow installation guidelines invalidates all warranties.
18.
Custom products/installations may not be reflected in this manual. Call
Draper, Inc., if you have questions about the installation of custom products
or any questions about your installation.
Before Beginning Installation
1.
Look for any job site conditions that could interfere with installation or
operation of the system.
2.
Read carefully and be sure to understand all installation instructions and
all related operations manuals. These instructions are intended to serve
as a guide for the installer and owner. They should be followed closely and
combined with the expertise of experienced qualified installers. Draper,
Inc., is not responsible for improper installation, application, testing, or
workmanship related to the product at place of installation. Please retain all
instructions for future use.
3.
Open cartons lengthwise.
4.
Locate and lay out all pieces.
5.
Inspect all boxes to make sure you have received the proper shade and
parts. Controls may be shipped separately, or in same carton as shade.
6.
If you have any difficulties with installing, servicing, or operating your shade,
call your dealer or Draper, Inc., 765-987-7999.
Important Safety Information
Important Safety Information
PLEASE READ -
Important Installation Information
PLEASE READ -
Safety Information
