Section 10 -
Complete Electrical Connection
Operates on 110-120V, 60 Hz. current. Shade is shipped with internal wiring complete and control switch
(es)
fully boxed, and supplied with a 6'
(183 cm)
cable lead
(standard)
. Longer lead can be substituted by removing two screws in motor end of roller, removing lead, plugging new lead in, and replacing screws. Wire to connect
shade to switch
(es)
and switch
(es)
to power supply should be furnished by installer. Connections should be made in accordance with attached wiring diagram, and
wiring should comply with national and local electrical codes.
DO NOT wire motors in parallel without written permission from Draper
®
.
All operating switches should be “off” before power is connected.
Section 9 -
Limit Setting: Standard and Quiet Motors
Caution:
Unit ships without limits. Limits will need to be set
before the unit is operated. Always be prepared to shut off
manually when new adjustment is being tested.
Push Button Limits
1.
Fully depress both limit switch push buttons, then
operate wall switch to make sure system works properly.
2.
Raise shade to desired "UP" stop position.
3.
Set upper limit by depressing proper
(back)
push button.
4.
Lower shade to desired "DOWN" stop position.
5.
Set lower limit by depressing proper
(front)
push button.
Screw-Type Limits
6.
Determine which direction of fabric travel corresponds
with arrows on motor.
Caution:
-
Be sure all switches are in "off"
position before adjusting limit
switches.
-
Shade may be damaged by
running shade fabric up too far
and exposing roller.
-
If using a group control system,
each limit switch must be set
prior to connecting to system.
-
Motor must be installed so
limit switches are pointed up or
accessible.
7.
Operate shade to desired "down" stop position.
Set limit by turning proper socket toward "+" to lower limit, and "-" to raise it.
8.
Operate shade to desired "up" stop position.
Set limit by turning proper screw toward "-" to raise limit, and "+" to lower it.
Please Note:
Each full rotation of the limit screw equals approximately
5/8
"
(16mm)
of shade travel, which may require rotating the limit screw
several times.
Caution:
DO NOT allow the hem bar to hit the upper roller or fascia.
This will damage the unit.
Caution:
DO NOT allow hem bar to retract into the headbox.
Controls & System Overview
Sonesse
®
RTS 120VAC Motors
B W G
RTS
MOTOR
120V
110-120V Line
Decora RTS
Wireless Keypad
Patio
RF Remote
STOP
Dashed Wiring
by Electrician
NOTE: Test shade operation
If shade direction does not
correspond with the switch
orientation, turn power back
off and switch the red and black
wires from the motor to the switch.
Do not wire motors in parallel without
written permission from Draper.
Controls & System Overview
Sonesse
®
120VAC Motors
W B R G
B
Control
Switch
Single Gang
Box (by others)
120V
MOTOR
110-120V Line
Dashed Wiring
by Electrician
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Front
Back
Bottom View
Side View
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
Screws
+
+
Front
Back
Bottom View
Side View
GLASS SIDE
ROOM SIDE
PUSH BUTTON LIMITS
Standard right-hand
motor configuration shown
SCREW-TYPE LIMITS
Standard right-hand
motor configuration shown
Sonesse
®
is a registered trademark of Somfy
®
Systems, Inc.
FlexShade
®
ZIP XL
page 8 of 11
