Optional Covers for 1⅝˝ brackets
Hardware for FlexShades
Clutch Brackets
Endcaps for Fascia and Headbox
Fascia Finishes
L Angle
Side Channel
7
/
8
"
7
/
8
"
1
5
/
8
"
1
5
/
8
"
Motor end
Idler end
Coupler assembly
FlexShade with motor
FlexShade without motor
FlexShade without motor
Surface-mounted Headbox is two piece plus endcaps.
4
⅝
Large box
3
⅜
Small box
4
⅝
Large bo
x
3
⅞
S
m
all bo
x
4
⅝
4
⅝
3
⅞
3
⅜
Large Pocket
Headbox
Small Pocket
Headbox
Configuration for pocket
installation (optional)
Pocket-Style Headbox
Wall Clip with Closure
Couplers
1
13
/
16
"
1
/
4
"
1
3
/
4
"
or 3"
Mounting Brackets—
The standard mounting hardware
supplied for wall, ceiling or jamb installation of
Draper Motorized
and
Manual FlexShades
. As an option for a pair of
⅝
brackets,
white bracket covers are available. If optional fascia or headbox are
specified, then endcaps (not brackets) are supplied.
Fascia—
Optional extruded fascia hides hardware and roller.
Available in clear anodized (standard), black, white, ivory, or charcoal
bronze.
⅞
or
⅝
high as required. Printed color at right may vary
from actual aluminum. Color samples are available.
Couplers—
Draper
’s
FlexShade
Coupling System
lets one
motor drive up to four additional shade rollers, or a crank operator
may drive two additional rollers. Coupled shades must be same height.
The overall width of a motorized group
may not exceed
; crank-operated groups
may be up to
wide.
Brackets extend
½
from mounting
surface to center line of roller, and may be
wall or ceiling mounted. Ideally, install
FlexShade
Coupling System
in
Draper
Type D Pocket
or existing pocket.
Coupled units may also be installed in
⅞
and
⅝
Draper
ceiling
pockets. Fascia is available. (Not suitable with
LightBloc
FlexShade
.)
Dimensions, drawings and specifications available at:
www.draperinc.com/go/FlexShadeCoupler.htm.
Side Channel or “L” Angle—
Side Channels or “L”
Angles prevent direct light gaps at sides of shade fabrics. Side
Ch
anne
ls are
deep x
½ wid
e, and mount to the jamb or face of
window opening. “L” Angles measure
¾
or
¾
and mount
inside the jamb.
Wall Clip with Closure—
Pocket already exists? Specify
FlexShade
Wall Clip with a long or short closure. Wall Clip mounts
to the wall and bottom closure panel drops neatly into place without
fasteners, leaving a minimal slot through which the shade descends.
For sleek appearance, use continuous wall clip. Closure sizes
¾
or
.
Surface-Mounted Headbox—
Complete extruded
headbox is available to hide hardware and roller as an option for
Motorized
and
Manual FlexShades.
Two-piece assembly is
suitable for surface mount to head, jamb or wall, in sizes
⅞
high or
⅝
high as required.
Pocket-Style Headbox—
Complete extruded headbox
with endcaps is available for ceiling recessed installation. In sizes
⅞
high or
⅝
high as required.
Custom Powder coating—
Custom powder coat paint
colors available for most
Draper
hardware. Contact
Draper
for
details. Powder coat provides an extremely durable, attractive finish.
Dimensions, drawings and specifications available at:
www.draperinc.com/go/FlexShadeHardware.htm.
www.draperinc.com
800-989-0126
16
