Draper SHADE SP, Installation & Operation Instructions

Section 1.3 - Mounting with Headbox

1. 

Snap endcap covers onto endcaps.

2. 

Place endcaps into back/top portion of wall/ceiling headbox or into pocket 

extrusion of pocket headbox. Using pre-drilled holes in endcaps, mark the 

headbox for drilling.

3. 

Drill holes in back or top, depending on whether you will be mounting the 

headbox to the wall, ceiling or pocket.

4. 

Attach endcaps and wall/ceiling headbox back/top or pocket headbox 

extrusion to wall, ceiling or pocket using mounting hardware appropriate for 

site conditions.

5. 

Install shade 

(see "With Endcaps" section above)

.

6. 

Attach headbox fascia or pocket closure 

(see Fig. 6 for pocket closure)

. Surface 

Headbox fascia is not fully seated until it clicks into place on both ends. 

Once in place, check for secure fit. If not secure, secure with appropriate 

fastener 

(not included)

.

Note on pocket style headbox, small size will require securing closure 

panel to endcap with provided screw.

Section 2 -

 Dimensions

Overall Width includes plastic endcap covers. 

(Pair adds 

1/8

" [3 mm] to Overall Width)

Shade Overall Width includes plastic endcap covers.  
Pair of small endcap covers adds 

1/8

" 

(3.2mm)

 to Overall Width.  

Pair of large endcap covers adds 

3/16

" 

(4.8mm)

 to Overall Width.

Above dimensions based upon 20 lb clutch and 1½" 

(38mm)

 diameter roller.

Please Note:

 When mounting brackets 

to the wall, use the hole closest to the 

wall. When mounting brackets to the 

ceiling, use the hole furthest away from 

the ceiling.

HEADBOX WITH ENDCAPS

SMALL

LARGE

A

1

3 

15/16

" 

100mm

4 

11/16

"

119mm

B

1

3 

7/16

"

87mm

4 

11/16

"

119mm

C

1

5/8

"

16mm

5/8

"

16mm

D

1

2"

51mm

3 

1/4

"

83mm

E

1

1/16

"

1.6mm

3/32

"

2.4mm

F

1

1 

3/16

"

30mm

1 

9/16

"

40mm

ENDCAPS WITH FASCIA

SMALL

LARGE

A

1

3 

7/8

" 

98mm

4 

5/8

"

117mm

B

1

3 

3/8

"

86mm

4 

5/8

"

117mm

C

1

5/8

"

16mm

5/8

"

16mm

D

1

2"

51mm

3 

1/4

"

83mm

E

1

1/16

"

1.6mm

3/32

"

2.4mm

F

1

1 

3/16

"

30mm

1 

9/16

"

40mm

BRACKETS

SMALL

LARGE

A

2

1 

3/8

"

35mm

1 

15/16

"

49mm

B

2

1 

15/16

"

49mm

2 

11/16

68mm

C

2

5/8

"

16mm

13/16

"

21mm

D

2

1 

5/8

"

41mm

2 

1/8

"

54mm

E

2

1 

1/4

"

32mm

1 

5/8

"

41mm

F

2

NA

NA

NA

NA

Outside Measurement (OM)

Cloth Width (CM)

(IM) = Outside Measurement (OM) with 

1

/

8

" (3 mm) deduction.

WINDOW OPENING

F

1

A

1

B

1

E

1

C

1

D

1

B

2

D

2

A

2

E

2

C

2

Please note:

 When measuring shade height, remember to 

include endcaps and fascia or headbox.

ATTACHING CLOSURE PANEL

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Large Pocket Headbox

STEP 1

STEP 2

STEP 3

Secure to Endcap

with Screw

Small Pocket Headbox

STEP 1

STEP 2

STEP 3

Figure 6

page 4 of 4

Spring Roller Shade