Draper STORMFORCE 65142, Instructions Manual

5.  HEALTH AND SAFETY INFORMATION

Wait for the machine to stop. 

Unless the machine is fitted with a safety brake; some parts may 

continue to move due to momentum. Wait for all parts to stop; then disconnect it from the air line 

before making any adjustments, carrying out maintenance operations or just finishing using the tool.

Remove and check setting tools. 

Some machinery requires the use of additional tools or keys to 

set, load or adjust the power tool. Before starting the power tool always check to make certain they 

have been removed and are safely away from the machine.

Prevent unintentional starting.

 Before connecting any machine in to the air supply, make sure 

the switch is in the OFF position. If the machine is portable; do not hold the machine near the 

switch and take care when putting the machine down; that nothing can operate the switch.

Concentrate and stay alert.

 Distractions are likely to cause an accident. Never operate a power 

tool if you are under the influence of drugs (prescription or otherwise), including alcohol or if you 

are feeling tired. Being disorientated will result in an accident.

Have this tool repaired by a qualified person.

 This tool is designed to confirm to the relevant 

international and local standards and as such should be maintained and repaired by someone 

qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains 

safe to use.

5.2 GENERAL SAFETY INSTRUCTIONS FOR COMPRESSED AIR

Following Safety instructions should be strictly followed. Failure to do so may result in accidents, 

equipment malfunctioning, serious personal Injury and / or loss of life.

Compressed air is a source of considerable energy. When handling products dealing with 

compressed air, the following precautions must be taken to prevent accidents.

1. Ensure that compressed air is not blocked or in contact with any part of your body.

2. Before connecting any pneumatic equipment to the compressed air supply, all mounted fittings, 

piping assemblies and electrical connections should be checked for security. All plastic plugs in 

the equipment used for protection during shipping should be removed.

3. No piping alterations, removal of fittings, repairing of equipment etc. Should be attempted with 

air supplies connected. Air and electrical supplies must be disconnected before beginning any 

adjustment, maintenance or dismantling of equipment.

4. The maximum allowable operating pressures, temperature, flows etc. must be strictly observed. 

Failure to do so might result in catastrophic failure of equipment, and result in serious personal 

injury and / or death. Refer to individual catalogues for this information, and any other operating 

or application limitations.

WARNING:

1. Compatibility of pneumatic equipment

Ensuring the compatibility of the procured FRL equipment is the responsibility of the person who 

designs the Pneumatic system and/ or System specifications. This should be based on 

specifications or after analysis and / or tests to meet specific requirements.

2. Repair & Maintenance

Assembly, handling, or repair of pneumatic systems should be performed by only trained and 

experienced operators.

3. Safety First

Do not service machinery / equipment or attempt to remove any component until safety Is 

confirmed.

i.  Inspection and maintenance of machinery / equipment should only be performed after 

confirmation that both compressed air and electrical supply have been positively disconnected 

and all residual compressed air in the system has been completely exhausted to the 

atmosphere.

4. Contact the manufacturer if equipment is to be used in any of the following conditions:

10. OPERATION

(2)

FIG.4

10.1 TRIGGER SWITCH - FIG. 4

Note: Before connecting the hammer to the air 

supply reduce the line pressure according to the 

specification.

-   Pull trigger 

(2)

 to operate the hammer.

-  Release the trigger to stop the hammer.

Note: Before tool operation and work 

commences, ensure the compressor reservoir is 

drained of condensate along with all connected 

air lines. Check and drain the air line regulator’s 

water trap and fill up the lubrication reservoir.

10.2 DUST AND SWARF

A correctly fitted dust mask, suitable for the 

activity and in accordance to the relevant 

standard, must be worn.

For work activities involving exposure to fine 

wood dust, a mask rated to at least FFP2 should 

be used.

The burr left on the workpiece edge is also sharp 

and should be removed with a suitable tool.

Always wear safety goggles.

Note: Disconnect from the air supply before 

carrying out adjustment, servicing or 

maintenance.

- 7 -

- 14 -

5.  HEALTH AND SAFETY INFORMATION

5.1 GENERAL SAFETY INSTRUCTIONS FOR POWER TOOL USE

When using any type of power tool there are steps that should be taken to make sure that you, as 

the user, remain safe.

Common sense and a respect for the tool will help reduce the risk of injury.

Read the instruction manual fully.

 Do not attempt any operation until you have read and 

understood this manual.

Most important you must know how to safely start and stop this machine, especially in an 

emergency.
Keep the work area tidy and clean.

 Attempting to clear clutter from around the machine during 

use will reduce your concentration. Mess on the floor creates a trip hazard. Any liquid spilt on the 

floor could result in you slipping.

Find a suitable location.

 If the machine is bench mounted; the location should provide good 

natural light or artificial lighting as a replacement. Avoid damp and dust locations as it will have a 

negative effect on the machine’s performance. If the machine is portable; do not expose the tool to 

rain. In all cases do not operate power tools near any flammable materials.

Keep bystanders away.

 Children, onlookers and passers by must be restricted from entering the 

work area for their own protection. The barrier must extend a suitable distance from the tool user.

Disconnect and house all power tools that are not in use.

 An air tool should never be left 

unattended while connected to the power supply. They must be housed in a suitable location, 

away locked up and from children.

Do not overload or misuse the tool.

 All tools are designed for a purpose and are limited to what 

they are capable of doing. Do not attempt to use a power tool (or adapt it in any way) for an 

application it is not designed for. Select a tool appropriate for the size of the job. Overloading a tool 

will result in tool failure and user injury: This covers the use of accessories.

Dress properly.

 Loose clothing, long hair and jewellery are all dangerous because they can 

become entangled in moving machinery: This can also result in parts of body being pulled into the 

machine. Clothing should be close fitted, with any long hair tired back and jewellery and neck ties 

removed. Footwear must be fully enclosed and have a non-slip sole.

Wear personal protective equipment (PPE).

 Dust, noise, vibration and swarf can all be 

dangerous if not suitably protected against. If the work involving the power tool creates dust or 

fumes; wear a dust mask. Vibration to the hand, caused by operating some tools for longer periods 

must be protected against. Wear vibration reducing gloves and allow long breaks between uses. 

Protect against dust and swarf by wearing approved safety goggles or a face shield. These are 

some of the more common hazards and preventions; however, always find out what hazards are 

associated with the machine/work process and wear the most suitable protective equipment 

available.

Do not breathe contaminated air.

 If the work creates dust or fumes; connect the machine (if 

possible) to an extraction system either locally or remotely. Working outdoors can also help if 

possible.

Move the machine as instructed.

 If the machine is hand held, do not carry it by the air line. If the 

product is heavy; employ a second or third person to help move it safely or use a mechanical 

device. Always refer to the instructions for the correct method.

Do not overreach.

 Extending your body too far can result in a loss of balance and you falling. This 

could be from a height or onto a machine and will result in injury.

Maintain your tools correctly. 

A well maintained tool will do the job safely. Replace any damaged 

or missing parts immediately with original parts from the manufacturer. As applicable; keep blades 

sharp; moving parts clean, oiled or greased; handles clean; and emergency devices working.

11. MAINTENANCE

11.1 EVERY-DAY MAINTENANCE CHECKS

Before connection to the air supply:
•  Drain the compressor reservoir of condensate.
•  Drain the air lines of condensate.
•  Drain the combined separator filter, regulator, water trap.
•  Fill up the combined separator filter, regulator, lubricant reservoir.
•  Check the line pressure is correct for the tool.

11.2 AFTER USE MAINTENANCE CHECKS

–  Repeat the above procedures.

–  Lubricate the tool with approximately 1.5ml of oil directly down the air inlet.

Warning!
●  Disconnect from the air supply before carrying out any adjustments, servicing or 

maintenance.

●  Never use any sockets or accessories that are not hardened for impact use.

- 6 -

- 15 -