Vigor2832 Series User’s Guide
681
wan budget wan [#] psday
[th day in periodic]
wan budget wan [#] action [action bitmap]
wan budget status
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
wan[#]
Specify the WAN interface.
rdate
Specify the WAN budget refresh time.
day – Available settings are from 1 to 30.
hour – Available settings are from 1 to 23.
E.g.,
wan budget wan 1 rdate 5 10
If monthy mode is selected: WAN budget will be refreshed on 5th
day at 10:00 in each month
If periodic mode is selected: WAN budget will be refreshed every 5
days and 10 hours
enable/disable
enable - Enable the function of wan budget.
disable - Disable the function of wan budget.
thres [budget limit (MB)]
Specify the maximum value for WAN budget limit. (Unit: MB)
budget limit – Type a number.
gthres [budget limit (GB)]
Specify the maximum value of wan budget limit. (Unit: GB)
budget limit – Type a number.
mode
[monthly|periodic|none]
Specify the calculation mode (monthly, periodically, or none) for
WAN budget.
psday
[th day in periodic]
It is used only when mode is set with “periodic”. Specify the order
of “today” in the cycle.
E.g.,
wan budget wan 5 psday
It means “today” is the 5
th
day
in the billing cycle.
action [action bitmap]
Determine the action to be performed when it reaches the WAN
budget limit.
action bitmap – Type a total number of actions to be executed.
Different numbers represent different actions.
1: shotdown wan
2: send mail alert
4: send sms alert
For example, if you type “5” (5=1+4), the system will send SMS alert
when WAN shotdown is detected.
status
Display current configuration status of WAN budget.
E
E
x
x
a
a
m
m
p
p
l
l
e
e
> wan budget wan 1 action 5
% WAN 1 budget action set to 5
> wan budget wan 1 gthres 10
% WAN 1 budget limit set to 10 GB
T
T
e
e
l
l
n
n
e
e
t
t
C
C
o
o
m
m
m
m
a
a
n
n
d
d
:
:
w
w
a
a
n
n
d
d
e
e
t
t
e
e
c
c
t
t
_
_
m
m
t
t
u
u
This command allows you to run a WAN MTU Discovery. The user can specify an IPv4 target to
ping and find the suitable MTU size of the WAN interface.
S
S
y
y
n
n
t
t
a
a
x
x
wan detect_mtu -w [number] -i [Host/IP address] -s [base_size] -d [decrease_size] (-c
[count])
S
S
y
y
n
n
t
t
a
a
x
x
D
D
e
e
s
s
c
c
r
r
i
i
p
p
t
t
i
i
o
o
n
n
Parameter Description
Summary of Contents for Vigor 3220 SERIES
