Draytek Vigor2920 Series User Manual Download | Manualshive

Page: 63 / 434

background image

Vigor2920 Series User’s Guide

53

Channel

Means the channel of frequency of the wireless LAN. The
default channel is 6. You may switch channel if the selected
channel is under serious interference. If you have no idea of
choosing the frequency, please select Auto to let system
determine for you.

Password

The wireless mode offered by this wizard is WPA2/PSK.

The WPA encrypts each frame transmitted from the radio
using the key, which either PSK (Pre-Shared Key) entered
manually in this field below or automatically negotiated via
802.1x authentication.

Either

8~63

ASCII characters, such as 012345678(or 64

Hexadecimal digits leading by 0x, such as
“0x321253abcde…”).

Next

Click it to get into the next setting page.

Cancel

Exit the wireless wizard without saving any changes.

3.

After typing the required information, click

Next

. The settings in the page limit the

wireless station (guest) accessing into Internet but not being allowed to share the LAN
network and VPN connection.

Available settings are explained as follows:

Item Description

Enable/Disable

Click it to enable or disable settings in this page.

Name

Type the SSID name of this router. (SSID2)

«
...
61
62
63
64
65
...
»

Summary of Contents for Vigor2920 Series



















































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Vigor2920 Series

Brand: Panasonic Pages: 4

Brand: Lab.gruppen Pages: 35

Adapter Bracket

Brand: Paradyne Pages: 1

Brand: Vivotek Pages: 170

Brand: Fortinet Pages: 20

EdgeLens INT10G8LR56

Brand: Garland Pages: 30

Barricade SMC7901WBRA2

Brand: SMC Networks Pages: 2

Brand: ICP DAS USA Pages: 8

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

Brand: XtendLan Pages: 228

Brand: Avaya Pages: 73

PG-Flex FLC-704

Brand: PairGain Pages: 20

Brand: Dahua Pages: 113

Brand: Rosco Pages: 20

Brand: netsys Pages: 164

Brand: Spirent Pages: 22

dLAN 200 AVsmart+

Brand: Devolo Pages: 2

LS-5100-16P-SI-OVS-H3

Brand: H3C Pages: 313

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands