Draytek Vigor3300V+ User Manual Download

Page: 140 / 230

Vig Series User’s Guide

132

Server Type

Select

Static

Dynamic

Custom

type for this entry of

DDNS settings.

Domain Name

Assign a private domain name to be accessed.

Login Name

Assign a name to login into DDNS server.

Login Password

Assign a password to login into DDNS server.

Wild Card

If you want anything-here.yourhost.dyndns.org to work (EX.
To make things like www.yourhost.dyndns.org work), click
“Enable” to active this function.

Backup MX

MX stands for Mail Exchanger. Mail Exchangers are used for
directing mail to specific servers other than the one a
hostname points at.

Mail Extender

Assign an email address.

Click

Apply

to finish these settings and return to previous page.

Note

1. The Wildcard and Backup MX features are not supported for all Dynamic DNS

providers. You could get more detailed information from their websites.

2. Backup MX provides a secondary mail server to hold your e-mail if your main email

server go offline for any reason. Once you go back online, your email will be delivered
to you.

Summary of Contents for Vigor3300V+







































































































































































































































Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands

Draytek Vigor3300V+, User Manual

Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands