background image

16 

-

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 12 

2.5

 

OPERATION 

a)

 

Water heating by electric energy 

 

After the heater is connected to electric network, the heating element starts heating water. The element 

 

is  turned  on  and  off  by  a  thermostat.  After  reaching  the  temperature  set,  the  thermostat  switches  off 

 

the electric circuit and discontinues water heating. The control light signals if the element is in operation 
(light is on) or if it is off (the light goes out). In case of longer operation without using the heated volume,

 

the thermostat has to be set to position 5°C to 8°C (set the “snowflake” symbol on the thermostat selector) 
to  avoid  its  freezing,  or  electricity  supply  to  the  heater  has  to  be  switched  off.  In  combined  versions, 

 

the stop valve on the inlet to the exchanger has to be closed at the inlet to the heat exchanger while which 
prevents heating the water in the hot water heating system.

 

 

b)

 

Service water heating via thermal energy through heat exchanger

 

 

 

Closing valves of the heat exchanger must be opened which ensures heating water flow from the hot water 
heating system. Together with the closing valve, it is recommended to install an air outlet valve at the inlet 
to the heat exchanger in order to bleed the heat exchanger as needed, in particular before the beginning 

 

of  the  heating  season  (Figure  9).  The  time  it  takes  to  heat  up  using  the  heat  exchanger  depends

 

on  the  temperature  and  flow  of  water  in  the  hot  water  heating  system.

 

A  combined  heater  is  made

 

in universal design 

depending on the need of connecting the closing valves to the heating element either 

from the right, or from the left.

 

 
 

2.6

 

FIRST COMMISSIONING 

After connecting the  heater  to  the  water  supply,  the  hot  water  heating  system,  the  electric 
network, and after testing its safety valve (based on the valve manual attached), the heater may 
be put into operation. Before opening the power supply, the tank must be filled with water.

 

The process of first heating must be executed by licensed professional who has to check it. Both 
the hot water outlet pipe and safety armature parts may be hot.

 

 

 

Summary of Contents for OKC 100 NTR/HV
























Reviews: