Sapporo Sleepmotion Lifestyle TV Bed
- safety information - Page 16
①
②
Disconnect all mains electric power to the bed, for at least 60 seconds.
Press either UP or DOWN Button on TV Lift Remote Control and keep holding button down,
simultaneously re-connect mains electric power to bed keeping button down for at least a
further 5 seconds. The TV Lift unit receives the signal from the Remote Control and TV lift will
begin to move UP or DOWN whichever button was pressed.
③
Re-pairing is now complete.
STOP
TV BED SAFETY INFORMATION
GENERAL INFORMATION
It is very important not to place any vessel containing liquids, e.g. drinks or vase of flowers, on top of the TV footboard which
may accidentally spill and enter the TV compartment as this could cause damage to the TV and/or the TV lifting equipment.
If this happens, please contact Customer Services - ring 0800 652 6750
.
For customers based in Northern Ireland, please call 028 9050 8300.
Do not expose the bed to an undue level of heat - keep away from radiators.
Never allow anyone to sit on the foot end of the bed - keep children well away from moving parts.
To keep the bed clean, we recommend that it be wiped over with a slightly dampened cloth or if fabric use a light vacuum
cleaner; disconnect power before cleaning.
Supplied with the TV bed is a remote control to operate the TV Lift and a remote control to operate the Television.
Both these remotes use batteries, there are strict controls for disposal of batteries - your local council can advise on how to
safely dispose of them. Never burn batteries on an open fire as they could explode.
IMPORTANT POWER INFORMATION
It is essential that the Mains Power Lead is connected to an earthed socket be it a wall socket or extension lead - otherwise
there is risk of damage or even electric-shock.
The socket providing the power must be accessible at all times in case one needs to switch o
ff
the supply quickly.
During an electrical or lightening storm - disconnect the power completely as a precaution.
Always un-plug the power when going on holiday or when the bed is not used for an extended period.
If you have young children in the home always disconnect the power at the wall socket for extra safety.
Power outlets, extension leads or adapters must not be overloaded beyond their limit - this can result in fire or electric shock
.
L
eads or leads supplied with this bed, or other approved mains powered extension leads used to power your own equipment,
must not be placed where they can be walked on - this is dangerous and could lead to accidents.
Do not interfere with or modify any leads already fitted and do not add any extra media leads unless they are routed through
the ducts as shown.
All leads must be tightly connected to back of TV using cable clips provided, never hanging loose.
Never touch moving parts or any part of the equipment - if something needs to be checked, disconnect the power first.
Do not insert anything into the footboard as this could seriously damage the TV and/or the TV lifting equipment and could, if
done carelessly, cause serious damage or injury.
If the equipment doesn't operate normally or if there is an unusual noise, disconnect the power
& contact Customer Services
.
TELEVISION INSTALLATION
Please follow the television installation instructions below.
Raise the TV Lift by pressing the
u
p button of the remote control.
Connect the Aerial & standard HDMI leads by passing down the appropriate duct
to suit connections on back of the TV
.
Connect the TV to the mounting bracket as appropriate taking care to follow the instructions.
If necessary mounting bracket can easily be adjusted
up or down to align with upper fixing holes on rear of TV.
Connect the TV Power Lead by passing the plug down one of the ducts, plugging it into an adapter if supplied, then into the
TV power socket which is on the face of footboard. This socket is only to be used for the TV as for safety reasons, the power
supply to it is not constant.
If required, connect your own media leads through either of the ducts - connect your media equipment when ready.
Please use the cable clips & cable ties to make certain there are no wires hanging loose that might get snagged or trapped.
The TV can now be operated following the TV User Guide supplied with your TV.
When finished viewing, lower the TV back into the footboard by pressing the
d
own button of the remote control, the TV will
retract into the footboard automatically - to prevent overheating, power shall be turned off when the TV reaches the lower rest
position.
When the
u
p button is pressed - the TV Lifting Column rises and power to the TV turns back on automatically.
TROUBLE SHOOTING
If your equipment does not operate please check all the power connections
from wall to the socket in the footboard.
Make sure TV is switched on (Note: TV will only work when it is in the up position).
If you cannot resolve an issue or still have a problem or need help, please contact Customer Services for advice.
IMPORTANT: Care should be taken when connecting electrical items. If you are in any doubt about the correct
connections to your TV Bed, please consult an approved electrician.
Occasionally you may find the radio wave connection between remote control and TV Lift is lost, probably due to atmospheric
conditions. In that case please follow these simple instructions:
UP
DOWN
