background image

DREHMO

 Instruction manual for USB adaptor kit 

page 3 of 20 

 

 

1  General 

 

1.1  Instructions 

 
The  following  signs  draw  special  attention  to  safety-relevant  procedures  in  these  operation 
instructions: 
 
 
 

This symbol signifies „additional information“. 
Failure to observe may lead to damage occurring. 
 
 
 
This symbol signifies „attention“. 
Failure to observe may result in damage and personal injury. 
 
 
 
This symbol signifies „warning!“ 
Failure to observe may result in damage and severe personal injury. 

 
 
 

SERVICE 
 

Service DREHMO GmbH 
fon.: +49 2762 9850-206 
fax:  +49 2762 9850-210 

 
 

1.2  Validity 

 
The usage of the described USB adaptor kit is only valid in combination with the DREHMO 
specific electrical units as described in detail in the following sections. The adaptors offer a 
mean  to  establish  a  serial  connection  between  a  PC  with  USB  interface  and  various 
intelligent electronic units. 
 

1.2.1  Requirements 

 
The  usage  of  the  USB  adaptor  kit  is  only  allowed  for  trained  staff.  The  knowledge  of  basic 
electronic and electric rules is required. 
 
 

A connection setup of the adaptor to the various electronic units is only allowed while 
the units are not powered. Safety instructions of the actuator instruction manual and 
the available electronic unit documentation have to be observed.  
 

 

Summary of Contents for c-matic





















Reviews: