Instruction ES2007 4/98
Models 4700P and 4700E
14
Hazardous Area Installations
The positioner is available in versions suitable for use in
hazardous areas. The labeling on the positioner indicates
correct areas of use.
WARNING: Installation of any hazardous area
equipment must be made in accordance with the
appropriate hazardous area installation codes
and the manufacturer’s installation and operat-
ing instructions. The user must make no changes
or attempt any repairs of a certified instrument
since this will invalidate the certified design. If a
certified instrument should fail it must be re-
turned to the manufacturer for repair.
Factory Mutual approved version
Explosionproof: Class I, Division 1, Groups B, C, and D.
Temperature classification T6 @ 75
°
C ambient, T5 @ 85
°
C
ambient, indoor and outdoor (NEMA Type 4X) hazardous
(classified) locations.
Dust-Ignitionproof: Class II / III, Division 1, Groups E, F,
and G.
Non-Incendive: Class I / II / III, Division 2 Groups A, B, C,
D, F, and G.
Installation must be in accordance with the current edition
of the National Electrical Code ANSI / NFPA-70, any
applicable local codes, and manufacturer’s instructions.
Intrinsically Safe: Class I / II / III, Division 1, Groups A, B,
C, D, E, F, and G hazardous indoor/outdoor NEMA 4X
locations. Temperature Classification T4 @ 40
°
C ambient,
T3B @ 70
°
C ambient, T3A @ 85
°
C ambient.
Installation must be in accordance with the current edition
of the National Electrical Code ANSI / NFPA-70, ANSI / ISA
RP 12.6
“Installation of Intrinsically Safe Instrument Sys-
tems in Class I Hazardous (Classified) Locations,” Figure
14, Installation Drawing 96-115 on page 15, and
manufacturer’s instructions.
CSA (Canadian Standards Association)
approved version
Explosionproof: Class I, Groups B, C, and D Class II,
Groups E, F, and G and Class III rated at 30 mA maximum,
28 Vdc maximum, with a temperature code T6 @ 75
°
C, T5
@ 85
°
C, Type 4X enclosure.
Division 2: Class 1, Division 2, Groups A, B, C, and D rated
30 mA maximum and 28Vdc maximum.
Installation must be in accordance with the current edition
of the Canadian National Electrical Code Part I, any appli-
cable local codes and manufacturer’s instructions.
Intrinsically Safe: Class I, Groups A, B, C, and D, Class II,
Groups E, F, and G, Class III rated at 30 mA maximum 28
Vdc maximum. Temperature code T6 @ 55
°
C, T4A @
85
°
C, Type 4X enclosure.
Installation must be in accordance with the current edition
of the Canadian National Electrical Code Part I, Figure 15,
Installation Drawing 96-112 on page 16, and manufacturer’s
instructions.
CENELEC Approved Version
Flameproof:
Coded as EEx d IIB + H
2
T5 @ Tamb = 70
°
C
T4 @ Tamb = 85
°
C
Type N:
Coded as Ex N IIC
T4 @ Tamb = -40
°
C to 80
°
C
Installation must be in accordance with current editions of
applicable country codes and manufacturer’s instructions.
Intrinsically Safe: Coded as EEx ia IIC T4 @ 80
°
C.
Installation must be in accordance with current editions of
applicable country codes, Figure 16, Installation Drawing
96-109 on page 17, and manufacturer’s instructions.
Housing Protection Rating IP 66
Split Range Operation
Split ranging permits operation of two valves in sequence
from one 4-20 mA control signal. To accomplish this with
the 4700E, the two positioners are connected in series as
shown in Figure 13, with the actual split ranging done by
proper cam segment selection per tables on pages 27 - 29.
Note: With this configuration, the voltage burden of the
4-20 mA controller is 10 V instead of 5 V.
Figure 13 - Split Range
Controller
Positioner
No. 1
Positioner
No. 2
Summary of Contents for Masoneilan 4700E
Page 15: ...15 Instruction ES2007 4 98 Models 4700P and 4700E Figure 14 FM Installation ...
Page 16: ...Instruction ES2007 4 98 Models 4700P and 4700E 16 Figure 15 CSA Installation ...
Page 17: ...17 Instruction ES2007 4 98 Models 4700P and 4700E Figure 16 CENELEC Installation ...
Page 32: ...Instruction ES2007 4 98 Models 4700P and 4700E 32 Figure 20 4700E Rotary Reciprocating ...
