background image

07-01742C F435-DV (110–230V UK) 

Legend Brands Holdings, Ltd. 

 

Owner’s Manual 

Dri-Eaz

®

 Building Dryer BD1000 

F435-DV (110–230V UK) 

Legend Brands Holdings, Ltd.  

22 Plover Close, Interchange Park, Newport Pagnell, MK16 9PS 

Tel: +44 (0)1908-611-211

 

Fax: +44 (0)1908-611-363

 

www.dri-eaz.co.uk

  

 

 

 

WARNING: Read and understand these warnings and instructions. 

 

DO NOT operate the unit with covers open or removed. 

 

WARNING: Do not alter or modify your BD1000 in any way. Use only replacement 

parts authorized by Dri-Eaz Products. Modifications or use of unapproved parts 

could create a hazard and will void your warranty. Contact your authorized Dri-

Eaz distributor for assistance. 

 

WARNING:  

Unplug before servicing.  

 

 

WARNING: ELECTRIC SHOCK HAZARD 

Unplug before opening cover.   

Use with a residual current device (RCD) where possible. 

Ensure power cord is properly earthed. 

Check that power cord is not damaged. 

Unplug before opening cover. 

 

 

WARNING:  

Moving parts may injure hands. Unplug before servicing.  

 

 

WARNING:  

Surfaces may be hot. Allow unit to cool before servicing.  

 

 
 
 

Summary of Contents for BD1000








Reviews: