background image

User Manual 

BUILT-IN GAS STOVE | 

GENOVA 90 

 

 

 

17 

              

-Burner ON, large flame          -Burner ON, small flame

saving mode

         -Burner OFF 

Fig.8

 

See fig.8 for various operating options (flame size selection); the burner should be set at a 
large  flame  during  the  initial  phase  of  cooking,  it  make  food  boil  quickly.  Then  should  turn 
knob to the saving flame position to maintain the cooking.  It is possible to adjust the flame 
size stepless. 

 
It is prohibited to adjust the flame between the Burner OFF and Burner ON large flame 
positions.

 

High quantity of energy can be conserved if the hob is used correctly, parameters are designed 
correctly, and appropriate cookware is used. The energy conservation be as follows

 

  Up to 60% are conserved when proper pots are used, 

  Up to 60% are conserved when the unit is operated correctly and the suitable flame 

size is chosen. 

It  is  a  prerequisite  for  efficient  and  energy-saving  operation  of  hob  that  the  burners  are  kept 
clean  at  all  times  (in  particular  the  flame  slots  and  nozzles).

 Adapting  to  different  types  of 

gas      

 

 

Adaptation to different types of gas 
 

APPLIANCE  CATEGORY: 

I

2H 

I

2E 

I

2E+ 

I

2L 

I

2HS 

I

2ELS 

I

2ELW 

I

3+ 

I

3B/P 

I

3B/P 

I

3B/P 

I

3P 

I

2H3+ 

II

2E3B/P 

II

2HS3B/P 

II

2

ELWLS3B/P II

2

ELL

3

B/P 

 

Burner 

Type of 

Gas 

Pressure 

Nozzle 

diameter 

Nominal Charge 

Reduced Charge 

mbar 

1/100mm 

g/h 

l/h 

kW 

kcal/h 

kW 

kcal/h 

Auxiliary  

Natural 

G20 

20 

71 

— 

95 

1.0 

860 

0.40 

344 

Butane 

G30 

30 

52 

72.6 

— 

1.0 

860 

0.40 

344 

Semi-rapid  

Natural 

G20 

20 

97 

— 

171 

1.8 

1548 

0.60 

516 

Butane 

G30 

30 

67 

130.8 

— 

1.8 

1548 

0.60 

516 

Rapid 

Natural 

G20 

20 

115 

— 

286 

3.0 

2580 

0.90 

774 

Butane 

G30 

30 

84 

226 

— 

3.0 

2580 

0.90 

774 

Summary of Contents for Genova 90




















Reviews: