background image

User Manual 

BULIT 

– IN GAS STOVE | 

LIVORNO 76 

Professionale

 

 

 

 

11 

DUAL TRIPLE FLAME VERSION 

 
         No gas flow  

 
   Maximum gas flow from central burner  
 

    Minimum gas flow from central burner.  

 
Gas flow from outside and burner center simultaneously.  
 
Minimum gas flow from outside and burner center simultaneously 
 

 

BURNER IGNITION 

 

• To obtain a flame, light the burner before placing the utensil on it. 
•  To  light  the  burner,  proceed  as  follows:  For  models  with  integrated  light  on  the  control 
knob,  push  fully  down  and  counterclockwise  to  the  maximum  flow  symbol  or  press  the 
button if the appliance is on individual. 
• Once the flame is switched on, press and hold the knob for about 10 seconds: This time is 
necessary to set the thermocouple (Fig.1  - C) and activate the safety valve; otherwise the 
gas flow will be cut off. 
• Then check the flame and turn the control knob to adjust the flame to the desired level. 
• In the event of a power failure, place a flame near the burner and proceed as described 
above. 
•  If  the  flame  does  not  come  on  after  several  attempts,  check  that  the  burner  and  flame 
cover is in the correct position. 
• To turn off the flame, turn the control knob clockwise to the symbol. 
• Before removing any utensils from the burners, always lower or turn off the flame.  

 
 
 
 
 
 
 
 
 

Summary of Contents for LIVORNO 76 Professional

















Reviews: