background image

User Manual 

BULIT 

– IN GAS STOVE | 

LIVORNO 76 

Professionale

 

 

 

 

13 

IGNITION SPARK PLUG 

 

Automatic burner ignition is provided (when installed) using ceramic plug and metal 
electrode.  Periodically  clean  this  part  of  the  burner.  Also,  to  avoid  difficulties  in 
ignition, make sure that the cavities in the burner are not clogged. 
To  remove deposits from  the burner  cavities,  remove  the  cover  and  separate 
the two parts (see diagram on the right). Once finished cleaning, replace both 
parts together and return it to the correct position. After washing, place the pan 
support, ensuring that it is correctly in position. 
 

ROUTINE MAINTENANCE 

 

Have the condition and efficiency of the gas line and the pressure regulator 
(if  installed)  periodically  checked.  If  anomalies  are  detected,  do  not  repair, 
but see that the defective part is replaced. 
To  ensure  proper  operation  and  safety,  the  gas  regulator  taps  should  be 
periodically greased. 
The lubrication of faucets must be periodically and by qualified personnel, 
who must always be in contact if the appliance does not work well 
.  

SERVICE AND PARTS 

 

Before  leaving  the  factory,  this  equipment  was  tested  and  adjusted  by  the  specialized 
personnel  to  give  the  best  operating  results.  All  subsequent  repairs  or  adjustments  must  be 
carried out with the utmost care and attention. 
For this reason, we always recommend contacting the distributor who sold the appliance or the 
nearest service center, specifying the nature of the problem, the equipment model (Mod.),  the 
product number (Prod. No.) And the number of series (Ser.No.). These data are on the cover 
of this manual. 
Always request the use of original spare parts.  

WARRANTY CONDITIONS 

 

• Your new appliance is covered by the warranty. The conditions of the guarantee can be seen in the 
certificate that you will find inside the product. 
•  Keep  the  tax  receipt  or  delivery  note,  as  well  as  the  purchase  documents  of  the  product  in  a  safe 
place together with the certificate of guarantee. 
• If you call the Technical Assistance Service, show these documents to the staff. If you do not follow 
these procedures, the facility will have no choice but to charge you for repairs. 
• If necessary, you can find in the warranty certificate the nearest service centers.  

Summary of Contents for LIVORNO 76 Professional

















Reviews: