background image

User Manual 

BUILT-IN GAS STOVE | 

LIVORNO 76 

 

 

 

3. HOW TO USE YOUR STOVE 

The position of the corresponding gas burner is indicated on each control knob. 

Gas burners 

The burners are different in size and power. Choose the most appropriate for the diameter of 
the kitchen utensils that are used. 

The  burner  can  be  adjusted  with  the  corresponding  control  knob  using  one  of  the  following 
configurations 

 

OFF 

      High 

          
          Low 
 

On those models equipped with a safety device 

The  knob  must  press and  after  being  on  wait  6  seconds,  then  release  the  knob  to  prevent  it 
from turning off when you turn it on since your account has a safety valve. 
 

To  light  a  burner: 

simply  press  the  corresponding  knob  and  turn  it  counterclockwise  to  the 

High setting, press and hold until the burner ignites. 

 
Caution: 

If  the  flame  accidentally  goes  out,  turn  off  the  gas  with  the  control  knob  and  try  to 

turn it on again at least 1 minute later. 

 
To turn off a burner: 

Turn the knob clockwise until it stops (it must be in the "•" setting). 

 
NOT ONE: 

 

Make sure that after you clean the kitchen the lids and burners should be well placed if 
they are not properly not going or the flame will be very high if it ignites. 

 

The wock holder goes over the burners, its function is to help better cooking since the 
pan is cooked at 360 degrees and not only in the middle. 

 
 
 
 
 
 
 
 
 
 

Summary of Contents for LIVORNO 76




















Reviews: