background image

User Manual 

RANGE HOOD | 

PRISMA ISLA 90 

 

 

 

 

5.  TROUBLE SHOOTING 

PROBLEM 

CAUSE 

SOLUTION 

the  machine  and  the  light  do 
not work after you’ve pressed 
the function key 

1 not plugged in properly 
2 The lamps are damaged 
3  The  wire  and/or  the  cable 
disconnected 
4  The  transformer  for  the 
lights is damaged 

1 Check the plug and insert completely 
2 Change the lamps 
3  Contact  the  distributor  and/or  service 
office 
4  Contact  the  distributor  and/or  service 
office 

Lights  work  and  the  motor 
don’t work 

1 The impeller is stopped 

The 

capacitor 

is 

disconnected 

and/or 

damaged 
3 The motor is damaged. 

1 Check and remove the blockage 
2  Contact  the  distributor  and/or  service 
office 
3  Contact  the  distributor  and/or  service 
office 

Shaking 

1  The  item  was  not  correctly 
hung 
2 The motor is too loose 

damaged 

impeller 

causes imbalance 

1 Hang the item stably 
2 Fasten the motor 
3  Contact  the  distributor  and/or  service 
office 

Only  one  of  two  keys  for  the 
motor work 

1 The switch is broken 
2  Bad  connection  with  the 
control board  

1  Contact  the  distributor  and/or  service 
office 
2  Contact  the  distributor  and/or  service 
office 

Insufficient suction 

1  The  vents  on  the  outlet 
cover not open completely 
2  There  is  too  much  airflow 
around the machine 
3 The oil filter is too dirty 
4  The  wire  and/or  cable 
damaged 

1  Lower  the  machine,  check  the  vents 
and loosen them. 
2 Close any open windows  
3 Clean it 
4 Have a mechanic fix it 

6.  CLEANING AND MAINTENANCE 

Never use metal abrasive pads, abrasive cleaners, or very stiff brushes. 

To clean the lightweight cover, use only a household cleaner diluted with water, then rinse 
with clean water and wipe dry with a soft cloth. 

Once the product is clean, it is recommended to apply mineral oil or baby oil to the 
steel with a clean, dry towel. For the cleaning of the glasses, we suggest to apply 
alcohol (with great caution) with a dry and clean towel

 

ESSENTIAL: 

Clean  these  filters  every  month  to  avoid  any  risk  of  fire.  The  filter  collects 

greasy  smoke  and  dust  and  is  an  element  that  plays  an  important  role  in  the  flammable 
when  saturated  with  fatty  residues.  Clean  it  with  a  commercial  household  cleaner,  then 
rinse  thoroughly  and  dry.  This  cleaning  can  be  done  in  your  dishwasher  with  the  filter 
upright (do not allow it to come in contact with dirty dishes and pans) 

Summary of Contents for Prisma Isla 90












Reviews: