8611/SM SIGNAL MONITOR OPTION
APPENDIX A
A-3
A.5 CONFIGURATION DETAILS
The WJ-8611 and the WJ-9168 are configured at the factory for the 8611/SM
implementation. No further action by the operator is required. The following
paragraphs discuss the configuration setup in detail.
WJ-8611
The WJ-8611 is configured for 8611/SM operation at the factory. The
8611/SM option is only compatible with WJ-8611 control software Version
01.01.00 or higher. In addition, the Digital Control PC Assembly has been
modified to provide a +13.5 Vdc supply voltage at A2J7, pin 3.
The operator may select between using the IEEE-488 interface or the interface
labeled RS-232 by front panel control. Upon activating one of the interfaces,
the other is deactivated. At power-up, the unit returns to the remote mode that
was active when the unit was powered down. With the 8611/SM option, DIP
switch settings on the Digital Control Board are set at the factory so that the
WJ-8611 defaults to the IEEE-488 interface upon loss of memory.
Figure A-1
depicts the factory settings for the WJ-8611’s A2S1 and A2S2
configuration switches when the 8611/SM option is installed. Refer to
paragraph 2.2.1
for detailed information on DIP switch setup and
paragraph
3.2.10
for information on selecting the remote interface from the front panel.
A2S1 SETTINGS
1
2
3
4
5
6
7
8
ON
NOTES:
OFF = 0; ON = 1
SEE
FO-11
FOR A2S1 AND A2S2 LOCATIONS.
WJ-8611 IS SET FOR IEEE-488 BUS ADDRESS OF 6 AT THE FACTORY.
DARK SEGMENTS DEPICT SWITCH POSITIONS.
A2S2 SETTINGS
1
2
3
4
5
6
7
8
ON
98
-04
28
Figure A-1. WJ-8611 A2S1 and A2S2 Settings for
8611/SM Option
WJ-9168
SMM
The WJ-9168 is configured at the factory for the implementation of the
8611/SM. No further action by the operator is required. The WJ-9168 is not
directly connected to the IEEE-488 bus; control is relayed by the WJ-8611 via
an RS-422 interface internal to the receiver. All required power is also
supplied by the WJ-8611. In the 8611/SM application, the WJ-9168 is
Courtesy of http://BlackRadios.terryo.org
Summary of Contents for WJ-8611
