AMB-600
Addressable Dual PIR Detector
INSTALLATION INSTRUCTIONS
©1999 Digital Security Controls Ltd.
Toronto, Canada
1-800-387-3630 • www.dscgrp.com
Printed in Canada 29002513 R004
Limited Warranty
Digital Security Controls Ltd. warrants that for a period of five years from the date of purchase, the product shall be free of
defects in materials and workmanship under normal use and that in fulfilment of any breach of such warranty, Digital Security
Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its repair depot.
This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or handling, or
damage due to causes beyond the control of Digital Security Controls Ltd. such as lightning, excessive voltage, mechanical
shock, water damage, or damage arising out of abuse, alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,
whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Digital
Security Controls Ltd. neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of
anticipated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or
operation or failure of this product.
Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions.
They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protec-
tion. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams.
They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows.
Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any material on the
lenses, mirrors, windows or any other part of the detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced
when the ambient temperature rises near or above body temperature or if there are intentional or unintentional sources of heat
in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbeques, fireplaces, sunlight,
steam vents, lighting and so on.
Warning: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis.
However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is
possible for this product to fail to perform as expected.
Important Information: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void the
user’s authority to operate this equipment.
The AMB-600 is a specialized Dual
PIR motion sensor which emphasizes
immunity from false alarms caused
by pets. The AMB-600 is equipped
with a specially designed lens* which
enables the detector to discriminate
between humans and small to mid-
sized pets.
Multi-Level Signal Processing**,
temperature compensation and large
multi-beam lens design means the
human target will not slip by
unnoticed even on a hot summer
day. Immunity against false alarms
from RF, static, electrical transients
and white light are all features
designed and integrated by DSC.
The AMB-600 uses a 2-wire
connection for power and to
communicate with the control panel.
This simplifies wiring and reduces
installation cost. The AMB-600’s low
current draw also maximizes the
number of devices that can be
attached to an addressable loop.
∗∗∗∗∗
Patented
∗∗
∗∗
∗∗
∗∗
∗∗
Protected by one or more of the following patents: Canada 2099971 US 5444432
Specifications
Current Rating ..................................................... 3.5 mA standby; 6.5 mA with Test LED on
Operating Environment ................................................................ 32°F to120°F / 0°C to 49°C
............................................................................................... 5% to 95% RH non-condensing
RF immunity ........................................... 10 V/m +80% A.M. over range, 80 MHz to 1.0 GHz
Static immunity ................................................................................................................. 15 kV
Transient immunity .................................................................................... 2.4 kV @ 1.2 joules
Walk detection speed ........................................................ 0.5'/s to 10'/s (0.15 m/s to 3 m/s)
Coverage angle ................................................................................................ 100° maximum
Vertical adjustment ................................................................................................. +5° to -10°
Mounting heights ................................................... 6' to 10' / 2m to 3 m (nominal 7.5' / 2.3m)
Dimensions ............................. 4.9" H × 2.76" W × 1.75" D (124.5 mm × 70 mm × 44.5 mm)
Tamper Switch Contact Rating ........................................................................ 0.1A @ 30 VDC
Control Panel Compatibility
PC4010/4020 v3.x
PC5010/5015 v2.x with PC5100 interface module
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your
authority to use this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict accordance
with the manufacturer’s instructions, may cause interference to radio and television reception. It has been type tested and
found to comply with the limits for Class B device in accordance with the specifications in Subpart “B” of Part 15 of
FCC Rules, which are designed to provide reasonable protection against such interference in any residential installation.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
interference to television or radio reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
•
Re-orient the receiving antenna
•
Relocate the alarm control with respect to the receiver
•
Move the alarm control away from the receiver
•
Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet prepared by the FCC helpful: “How to Identify and
Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Printing
Office, Washington, D.C. 20402, Stock # 004-000-00345-4.
DM-C and DM-W: Detector Mounting Brackets
Use the optional DM-W Wall Mount and DM-C Ceiling Mount brackets to solve
difficult placement problems. The DM-W and DM-C mount to either the wall or
ceiling and allow for full vertical and horizontal positioning of the motion detector
- the detector can be tilted up or down and rotated through 90° to obtain the best
position for optimal coverage.
