DSC PC1555 CP-01 Installation Manual Download

Page: 36 / 56

Alarm Cancelled:

this reporting code will be sent if a valid

access code is entered during the Alarm Cancel window.
If a valid access code is entered during this window, then
the Alarm Cancelled event is logged and sent. When the
central station has acknowledged this reporting code/
event, a keypad ring-back will occur.

[329] - Priority Alarm and Restoral Reporting
Codes

[F], [A], [P] Alarm:

this reporting code will be sent if the

[F] [A] or [P] key is used to generate manual alarms.

Auxiliary Input Alarm:

this reporting code will be sent

when PGM2 is being used for 2-wire smoke detectors and
the 2-wire smoke detector goes into alarm.

[F], [A], [P] Restoral:

this reporting code will be sent after

the [F] [A] [P] alarm reporting code is sent.

Auxiliary Input Restoral:

the panel will transmit this

reporting code when the 2-wire smoke detector has
restored after an alarm.

[330]-[331] - Tamper Reporting Codes, Zones 1-32

If the panel is programmed for Double EOL zones (see
Section 2.10 "Zone Wiring") the panel will report a

Zone

Tamper Alarm

reporting code if an open condition is

present on a zone. A different reporting code can be pro-
grammed for each zone for identification.

[334]-[335] - Tamper Reporting Codes, Zones 1-32

The

Zone Tamper Restoral

reporting code will be trans-

mitted immediately when the Tamper condition is
restored.

[338] - Miscellaneous Tamper Reporting Codes

General System Tamper:

a General System Tamper

General System Tamper

General System Tamper Report-

ing code will be transmitted when the tamper zone on
any module is violated.

General System Tamper Restoral:

the General System

General System

Tamper Restoral

Tamper Restoral reporting code will be transmitted when
the tamper zone on the module is restored.
Keypad Lockout:

Keypad Lockout:

Keypad Lockout: the panel will transmit the Keypad

Keypad

Lockout

Lockout reporting code if the lockout is activated.

[339]-[340] - Closing (Arming) Reporting Codes,
Access Codes 1-32

The panel will transmit a Closing

Closing

Closing reporting code to indi-

cate the system is armed. A different reporting code can
be transmitted for each User Code, Partition Master Code
and System Master Code to identify who armed the sys-
tem.

[341] - Miscellaneous Closing (Arming) Reporting
Codes

Closing by Duress Code 33/34:

a Closing by Duress

Closing by Duress

Closing by Duress code

Reporting code will be transmitted in addition to the
Duress reporting code if the system is armed using a
Duress Code.

Closing by Master or Supervisory Code:

the panel will

transmit a Closing

Closing

Closing reporting code to indicate the system

is armed. A different reporting code can be transmitted
for each User Code, Supervisory Code and System Master
Code to identify who armed the system.

Partial Closing:

a Partial Closing

Partial Closing

Partial Closing reporting code will be

transmitted if the system is armed with zones manually
bypassed. The code will also be transmitted if the system
Auto-arms with zone(s) in violation.

Special Closing:

a Special Closing

Special Closing

Special Closing reporting code will be

transmitted if tthe system is armed using any of the fol-
lowing methods:

Quick Arm
Auto-arm
Arming via the DLS Software

Arming via Keyswitch
Away Function Key Arming
Arming with the Maintenance Code.
Stay Function Key arming

Late to Close

A Late to Close

Late to Close

Late to Close reporting code will be

transmitted if the system isn't armed before the auto-arm
start time when the late to close option, (Section 017,
option 5) is enabled.

Exit Fault:

If an Exit Fault Pre-Alert

Exit Fault Pre-Alert

Exit Fault Pre-Alert occurs and Entry

Delay expires before the system is disarmed, Exit Fault
will be logged and this reporting code will be sent.

[342]-[343] - Opening (Disarming) Reporting
Codes Access Codes 1-32

The panel will transmit an

Opening

reporting code

to indi-

cate the system is disarmed. A different reporting code
can be transmitted for each user code, the system master
code and system master code to identify who armed the
system.

[344] - Miscellaneous Opening (Disarming)
Reporting Codes

Opening by Duress Code 33/34:

Opening by Duress Code 33/34: This reporting code will be
transmitted in addition to the duress reporting code if the
system is disarmed using a Duress Code
Opening by Master or Supervisory Code:

Opening by Master or Supervisory Code:

Opening by Master or Supervisory Code: The panel will
transmit this reporting code to indicate the system is
armed. A different reporting code can be transmitted for
each User Code, Supervisory Code and System Master
Code to identify who armed the system.
Auto Arm Cancellation:

Auto Arm Cancellation:

Auto Arm Cancellation: This reporting code is transmitted
when the Auto Arming sequence is canceled or Postponed
Special Opening:

Special Opening:

Special Opening: A Special Opening

Special Opening

Special Opening reporting code will

be transmitted if the system is disarmed using any of the
following methods:

• Disarming using the Maintenance Code
• Disarming via the DLS Software
• Disarming via keyswitch

[345] - Maintenance Alarm Reporting Codes

Battery Trouble Alarm:

the panel will transmit a Battery

Battery

Trouble Alarm

Trouble Alarm reporting code when the backup battery
drops below 11.5 V

AC Failure Trouble Alarm:

the panel will transmit an AC

Failure Trouble Alarm

Failure Trouble Alarm reporting code when the AC to the
panel is lost and the AC Failure Communication Delay
timer expires.

Bell Circuit Trouble Alarm:

a Bell Circuit Trouble Alarm

Bell Circuit Trouble Alarm

reporting code will be transmitted immediately if an open
condition is measured on the Bell Output of the main
panel.

Fire Trouble Alarm:

a Fire Trouble Alarm

Fire Trouble Alarm

Fire Trouble Alarm reporting code

will be transmitted immediately when an open condition
is measured on any fire zone.

Auxiliary Power Supply Trouble Alarm:

the Auxiliary

Auxiliary

Power Supply Trouble Alarm

Power Supply Trouble Alarm reporting code will be
transmitted if the AUX output is shorted.

TLM Trouble:

a TLM Trouble

TLM Trouble

TLM Trouble reporting code can only be

transmitted if a LINKS1000/2X50 Communicator is being
used (see Section 5.26 LINKS1000 Cellular Communica-
tor). The panel will only transmit the signal after the time
programmed for the TLM Trouble Delay.

General System Trouble:

a General System Trouble

General System Trouble

General System Trouble report-

ing code will be transmitted if the panel detects any of the
following:

AC Power Failure
Low Battery
AUX Output Trouble