iotega Wireless Security and Automation System
Safety Instructions for Service Persons
Warning: When using equipment connected to the telephone network, always follow
the basic safety instructions provided with this product. Save these instructions for
future reference. Inform the end-user of the safety precautions that must be observed
when operating this equipment.
Before Installing The Equipment
Ensure your package includes the following items:
l
Installation and User manuals, including the SAFETY INSTRUCTIONS.
READ and SAVE these instructions!
Follow all WARNINGS AND INSTRUCTIONS specified within this doc-
ument and/or on the equipment.
l
iotega alarm controller
l
Power Supply, direct plug-in
l
Ethernet cable
Selecting A Suitable Location For The Alarm Controller
Use the following list as a guide to find a suitable location to install this equipment:
l
Locate near a power outlet.
l
Select a location free from vibration and shock.
l
Place alarm controller on a flat, stable surface and follow the installation
instructions.
Do NOT locate this product where people may walk on the secondary circuit cable(s).
Do NOT connect alarm controller to electrical the same circuit as large appliances.
Do NOT select a location that exposes your alarm controller to direct sunlight, excess-
ive heat, moisture, vapors, chemicals or dust.
Do NOT install this equipment near water. (e.g., bath tub, kitchen/laundry sink, wet
basement, near a swimming pool).
Do NOT install this equipment and accessories in areas where risk of explosion
exists.
Do NOT connect this equipment to electrical outlets controlled by wall switches or
automatic timers.
AVOID interference sources.
AVOID installing equipment near heaters, air conditioners, ventilators, and
refrigerators.
AVOID locating equipment close to or on top of large metal objects (e.g., wall
studs).
See "Locating Detectors and Escape Plan" on page 1 for information on locating
smoke and CO detectors.
SAFETY Precautions Required During Installation
l
NEVER
install this equipment during a lightning storm.
l
Position cables so that accidents can not occur. Connected cables must
NOT be subject to excessive mechanical strain.
l
Use only the power supply provided with this equipment. Use of unauthorized
power supplies may cause damage.
WARNING: THIS EQUIPMENT HAS NO MAINS ON/OFF SWITCH. THE
PLUG OF THE DIRECT PLUG-IN POWER SUPPLY IS INTENDED TO
SERVE AS THE DISCONNECTING DEVICE IF THE EQUIPMENT MUST
BE QUICKLY DISCONNECTED. IT IS IMPERATIVE THAT ACCESS TO
THE MAINS PLUG AND ASSOCIATED MAINS SOCKET/OUTLET IS
NEVER OBSTRUCTED.
IMPORTANT NOTE FOR NORTH AMERICA!
This alarm system must be installed and used within an environment that
provides the pollution degree max 2 and over-voltages category II NON-
HAZARDOUS LOCATIONS, indoor only. The equipment is DIRECT
PLUG-IN (external transformer) and is designed to be installed, serviced
and/or repaired by service persons only; [service person is defined as a
person having the appropriate technical training and experience necessary
to be aware of hazards to which that person may be exposed in performing
a task and of measures to minimize the risks to that person or other
persons]. This equipment has no mains on/off switch; if the equipment must
be quickly disconnected, the plug of the direct plug-in power supply is
intended to serve as the disconnecting device; it is imperative that access to
the mains plug and associated mains socket/outlet, is never obstructed.
There are no parts replaceable by the end-user within this equipment. The
wiring (cables) used for installation of the alarm system and accessories,
shall be insulated with PVC, TFE, PTFE, FEP, Neoprene or Polyamide.
(a) Internal wiring must be routed in a manner that prevents:
- Excessive strain or loosening of wire on terminal connections;
- Damage of conductor insulation
(b) Disposal of used batteries must be made in accordance with local waste
recovery and recycling regulations.
(c) Before servicing, DISCONNECT the power.
(d) DO NOT route any wiring over circuit boards.
(e) The installer is responsible to ensure that a readily accessible disconnect
device is incorporated in the building for permanently connected
installations.
The power supply must be Class II, FAIL SAFE with double or reinforced
insulation between the PRIMARY and SECONDARY
CIRCUIT/ENCLOSURE and be an approved type acceptable to the local
authorities. All national wiring rules must be observed.
IMPORTANT NOTE FOR INTERNATIONAL MARKET (EU,
AUS, NZ)!
This equipment is stationary-fixed and must be installed by Service Persons
only (Service Person is defined as a person having the appropriate technical
training and experience necessary to be aware of hazards to which that
person may be exposed in performing a task and of measures to minimize
the risks to that person or other persons). It must be installed and used
within an environment that provides the pollution degree max 2, over
voltages category II, in non-hazardous, indoor locations only. When using
equipment connected to the mains and/or to the telecommunication
network, there are basic safety instructions that should always be followed.
Refer to the safety instructions provided with this product and save them for
future reference. To reduce the risk of fire, electric shock and/or injury,
observe the following: Do not attempt to service this product yourself.
Opening or removing the cover may expose you to dangerous voltage or
other risk. Refer servicing to qualified service persons. Use authorized
accessories only with this equipment. DO NOT leave and/or deposit ANY
object on the top of the cabinet of this equipment! The cabinet as it is
installed on the wall is not designed to support any supplementary weight!
Do not spill any liquids on the cabinet or equipment. Do not touch the
equipment and its connected cables during an electrical storm; there may be
a risk of electric shock. Never touch uninsulated wires or terminals unless
the equipment has been disconnected from the mains supply and from the
telecommunication network! Ensure that cables are positioned so that
accidents cannot occur. Connected cables must not be subject to excessive
mechanical strain. Do not use the Alarm system to report a gas leak if the
system is near a leak.
These safety instructions should not prevent you from contacting
the distributor and/or the manufacturer to obtain any further cla-
rification and/or answers to your concerns.
- 1 -
